Applications and Uses of Zero Spangle Galvanised Steel Coils (SGCC, SGCD, SGCE)

Oct 23, 2025 Leave a message

What Zero Spangle Means on a Galvanised Coil

Spangle is the visible crystalline zinc pattern that forms when a hot-dip galvanised coating solidifies on the steel surface. In a zero spangle product the growth of those zinc crystals is suppressed during cooling, so the surface appears uniform, matte and free from the fern-leaf pattern seen on ordinary galvanised sheet. This is normally achieved by controlling the molten zinc bath chemistry, typically with small additions of antimony or tin, and by adjusting the cooling rate immediately after the coating pot. Zero spangle material is usually skin-passed as well, which flattens the coating slightly and gives the sheet a defined surface roughness.

For the user the difference is practical rather than decorative. A uniform surface accepts paint and powder coating evenly, provides more consistent friction during forming, and removes the visual variation that would otherwise show through a thin paint film on visible parts such as appliance panels and cladding.

Grades: SGCC, SGCD and SGCE

Zero spangle coils are supplied in several grade families. The JIS G3302 series describes commercial, drawing and deep-drawing qualities, while the European harmonised standard EN 10346 covers the DX and S construction grades. These designations are not freely interchangeable, so the grade printed on the mill certificate should always be checked against the drawing or the purchase specification before production starts.

Grade Standard Character Typical use
SGCC JIS G3302 Commercial quality, general forming Purlins, panels, ducting, enclosures
SGCD JIS G3302 Drawing quality, tighter formability Appliance parts, drawn housings
SGCE JIS G3302 Deep-drawing quality Complex drawn components
DX51D+Z EN 10346 Bending and profiling grade Roofing, wall cladding, general fabrication
DX52D+Z / DX53D+Z EN 10346 Increasing drawing quality Formed covers, housings, shells
S250GD+Z to S550GD+Z EN 10346 Structural grades with defined yield strength Load-bearing profiles, purlins, frames

Typical Specifications

Item Range
Spangle type Zero spangle (matte, uniform)
Zinc coating mass Z100 to Z275 g/m2 total both sides, lighter coatings for indoor parts
Thickness 0.45 mm to 4.75 mm
Width 900 mm to 1260 mm, or cut to order
Coil inner diameter 508 mm or 610 mm
Coil weight Up to about 10 t
Substrate grades DX51D+Z to DX56D+Z, S250GD+Z to S550GD+Z, SGCC, SGCD, SGCE
Surface treatment Chromate passivation, anti-fingerprint oil, or dry and untreated
Certification CE marking and ISO 9001 quality management

Because the base steel is selected for hardness and tensile strength, zero spangle sheet is normally produced from tightly controlled cold-rolled substrate. Any deviation in the substrate surface shows up more clearly after skin-passing, so incoming inspection should cover flatness, edge condition and coating mass rather than appearance alone.

Applications Across Industries

Construction: roofing and wall cladding, purlins and secondary framing, wall ties, ducting, and architectural trim where a uniform painted finish matters.

Automotive: inner body panels, brackets, seat frames, heat shields and underbody parts where coating adhesion and consistent forming behaviour are required.

Household appliances: refrigerator and freezer side panels, washing machine wrappers, oven and air-conditioning casings, where a smooth paint base is essential.

Electrical equipment: control cabinets, distribution boxes, cable trays and switchgear housings, where the zinc coating protects against humid service conditions.

General sheet metal: shelving, lockers, furniture frames, HVAC ducting and signage.

Fabrication, Painting and Storage

Zero spangle coil performs well in the usual sheet-metal operations: slitting, shearing, laser cutting, CNC punching, roll forming, bending and press forming. Coating adhesion is normally verified with a bend or impact test on a sample from each coil lot, and coating mass with a stripping test in line with ISO 1460 or the relevant reference method in EN 10346 and ASTM A653/A653M.

For painted parts, a phosphate pre-treatment followed by electrostatic powder coating or a liquid primer gives the most reliable result, because the matte surface mechanically keys the film and covers the cut edges that would otherwise be the first points to rust. Chromated or oiled surfaces must be cleaned before coating, and welding areas should be stripped of oil to avoid porosity.

Storage also matters. Coils and sheets should be kept indoors on dry timber or plastic supports, with ventilation between stacked sheets, and protected from condensation during transport. Water trapped between sheets is the most common cause of white rust, and it is easy to prevent with correct packing and short storage times.

Frequently Asked Questions

Q: Is zero spangle galvanised coil the same as ordinary galvanised coil?
The steel substrate and the zinc coating are the same; only the coating appearance and surface roughness differ. Zero spangle sheet has a matte, uniform finish instead of a visible crystalline pattern.

Q: Which is better for painting, zero spangle or regular spangle?
Zero spangle is generally preferred for visible painted parts. Its uniform texture gives more even coverage and fewer paint defects than the raised crystal pattern of regular spangle.

Q: Does the zinc coating mass affect corrosion life?
Yes. Within the same environment, a heavier coating such as Z275 lasts considerably longer than Z100. Indoor components rarely need the heaviest class, while exposed outdoor parts normally do.

Q: Can zero spangle coils be welded?
Yes, using resistance spot welding or conventional arc processes. Because the zinc coating vaporises at welding temperature, adequate ventilation and correct electrode force are important, and the weld zone should be recoated for corrosion protection.

Q: How should coating adhesion be checked before mass production?
A bend test around a defined radius, an impact test and a tape pull after forming are the usual shop-floor checks. Samples should be taken from the head, middle and tail of each coil.

Q: What causes white rust on stored coils?
White rust is zinc corrosion product formed when moisture is trapped between sheets or when condensation cycles occur. Dry indoor storage, ventilation and prompt use prevent it.