SGCC-ZAM Zinc-Aluminum-Magnesium Coated Steel Coil
SGCC-ZAM Zinc-Aluminum-Magnesium Coated Steel Coil

SGCC-ZAM Zinc-Aluminum-Magnesium Coated Steel Coil

SGCC-ZAM is a trade shorthand for commercial-quality cold-rolled base steel with a continuous hot-dip zinc-aluminum-magnesium (Zn-Al-Mg) coating.
Send Inquiry
Chat Now

Get a free quote! Contact us today!

Send E-mail: sale@gneegi.com

Tel: +86 15824687445

SGCC-ZAM is a trade shorthand for commercial-quality cold-rolled base steel with a continuous hot-dip zinc-aluminum-magnesium (Zn-Al-Mg) coating. The coating makes the difference: zinc, aluminum and magnesium build a dense corrosion layer that spreads over scratches and sheared edges.

Zinc-Aluminum-Magnesium Coated Steel Coil
Zinc-Aluminum-Magnesium Coated Steel Coil

SGCC-ZAM Zinc-Aluminum-Magnesium Coated Steel Coil

 

1. What the Name Actually Commits To

Reading the name correctly prevents most disputes.

 

  • SGCC points to a commercial-quality cold-rolled substrate. Yield strength is not guaranteed; bending performance is the controlling requirement.
  • ZM / ZAM identifies the coating family, not a coating mass. A number must follow it.
  • JIS G 3323 uses NSDC-style substrate symbols and K-series coating symbols. K27, for example, means a triple-spot average of 275 g/m² on both sides.

 

For an equivalent under EN 10346, buyers usually write DX51D+ZM275. "X" again means no guaranteed yield. The substrate decides how far the material can be formed; the coating decides how long it survives in service.

 

2. SGCC-ZAM Product Specifications

Item

Available specification

Substrate

Commercial quality, cold rolled (SGCC / DX51D-type)

Coating

Zn-Al-Mg, typically Zn balance with 1-11% Al and 1-4% Mg, trace Si

Coating mass

ZM100 / ZM120 / ZM150 / ZM180 / ZM220 / ZM275

Thickness

0.30-3.0 mm, commonly 0.5-2.0 mm

Width

600-1,500 mm, slit or full coil

Coil ID

508 mm or 610 mm

Coil weight

3-10 t, customized to order

Surface

Oiled, dry, chemical treated or anti-fingerprint

Edge

Mill edge or slit edge

Certificate

Mill test certificate, EN 10204 3.1 available

All figures are supply ranges. Confirm the exact combination against the mill certificate before release.

 

Send Your Requirements

 

3. Coating Mass: Read Two Numbers, Not One

A coating grade is a mass per square metre, measured over both sides. JIS G 3323 reports a three-spot average and a single-spot minimum. The second number is the one that catches weak areas.

Coating symbol

Triple-spot average (g/m², both sides)

Single-spot minimum (g/m²)

K12 / ZM120

120

102

K18 / ZM180

180

153

K22 / ZM220

220

187

K27 / ZM275

275

234

Specify both values in the purchase order. A supplier quoting only the average has not committed to the minimum.

 

4. Forming and Corrosion Behaviour

Commercial-quality substrate carries no specified minimum yield. For the DX51D-type equivalent, EN 10346 gives tensile strength of 270-500 MPa and A80 elongation of at least 22% for thickness of 0.70 mm or more. Thinner gauges use lower limits, so quote the thickness when requesting mechanical values.

 

The Mg-rich coating produces compact zinc-magnesium corrosion products that migrate across cut edges. That is why ZM outperforms plain zinc most clearly after slitting, punching and roll forming. Published ASTM B117 ranges put Z275 around 300-500 hours and ZM275 around 2,000-3,000 hours before red rust. These are laboratory comparison bands, not a design life.

 

5. Typical Applications

Solar mounting rails, posts, purlins, bracing and base plates

Roofing and wall cladding in coastal or industrial atmospheres

Cold-formed sections, cable trays and ventilation ducting

Agricultural structures and equipment housings

Appliance panels and automotive structural parts

For coastal or high-humidity projects, start at ZM275. Inland dry service is usually covered by ZM120 to ZM180.

 

6. Quality Control and Documents

Every order is checked for grade identification, thickness and width, coating mass, surface condition, mechanical properties and coil weight. Mill test certificates record heat number and test results. Third-party inspection by SGS, BV or TÜV can be arranged before shipment. Export coils are wrapped with moisture barrier film, edge protection and steel strapping.

 

7.Case Studies

 

GNEE STEEL recently welcomed valued Thai clients to our factory. The delegation conducted on-site inspection and technical exchanges. Both sides reached cooperation agreement on steel supply for Thai infrastructure projects. We look forward to long-term win-win partnership and supporting Southeast Asia's construction development.

SGCC-ZAM steel
SGCC-ZAM steel
SGCC-ZAM steel
 
 
 

FAQ

 

1.Is SGCC-ZAM a Japanese standard grade?

SGCC belongs to JIS G 3302; Zn-Al-Mg coated sheet belongs to JIS G 3323. "SGCC-ZAM" is common trade shorthand for the combination, so state the standard explicitly on the order.

 

2.Can SGCC-ZAM replace galvanized steel directly?

Often yes, after checking forming radius, coating mass and joining method. The higher coating hardness may require a slightly larger inside radius on tight bends.

 

3.Which coating mass suits a coastal project?

ZM275 is the usual starting point. Aggressive C5 environments may call for a heavier coating, confirmed against ISO 9223 exposure class.

 

4.Can you supply sample coils for trial forming?

Yes. Tell us the thickness, width and coating mass and we will arrange a sample for your slitting or roll-forming trial.

 

Send your SGCC-ZAM specification to our team and receive a confirmed quotation, certificate sample and lead time within 24 hours. Small trial quantities are accepted.

Hot Tags: sgcc-zam zinc-aluminum-magnesium coated steel coil, China sgcc-zam zinc-aluminum-magnesium coated steel coil manufacturers, suppliers, factory