General Product Description
The ASTM A709 is the Standard Specification for Structural Steel for Bridges and encompasses carbon, high-strength low-alloy, and quenched and tempered alloy steels used as structural plates in the construction of bridges. SSAB offers the following five grades of A709; 36, 50, 50W, HPS 50W and HPS 70W. The three weather grades of 50W, HPS 50W, and HPS 70W have an ASTM G101 enhanced Atmospheric Corrosion Resistance Index of ≥6.0.
Available Dimensions
Hide/Show specific columns EDIT
| GRADE | THICKNESS (in) |
WIDTH (in) |
LENGTH (in) |
|---|---|---|---|
| 50 | 0.1875 - 3.00 | 72 - 120 | 240 - 1200 |
| 50T | 0.1875 - 3.00 | 72 - 120 | 240 - 1200 |
| 50F | 0.1875 - 2.50 | 72 - 120 | 240 - 1200 |
| 50F | 2.51 - 3.00 1) | 72 - 120 | 240 - 1200 |
Width: Please inquire for plate widths less than 72 in. and over 120 in. Inquire for widths greater than 96 in. for thicknesses less than 0.250 in.
Length: Please inquire for plate lengths greater than the listed maxima. Plate length may be limited by maximum individual plate weight of 66,000 lbs. Plate length maximum of 960 in. for thicknesses less than 7/16 in.
1) Please inquire for thicknesses greater than 2.50 inches up to 3.0 inches.
Mechanical Properties
Tensile testing is performed in the transverse direction according to ASTM A370 requirements.
Hide/Show specific columns EDIT
| GRADE | THICKNESS (in) |
YIELD STRENGTH 1) (MIN ksi) |
TENSILE STRENGTH (MIN ksi) |
ELONGATION IN 2" 2) (MIN %) |
ELONGATION IN 8" 2) (MIN %) |
|---|---|---|---|---|---|
| 50 | 0.1875 - 3.00 | 50 | 65 | 21 | 18 |
| 50T | 0.1875 - 3.00 | 50 | 65 | 21 | 18 |
| 50F | 0.1875 - 3.00 | 50 | 65 | 21 | 18 |
1) Yield strength measured as 0.2% offset or 0.5% extension under load.
2) For plates wider than 24 in, the elongation requirement is reduced by two percentage points. See elongation requirement adjustments in the Tension Test section of Specification ASTM A6.
Impact Properties
Hide/Show specific columns EDIT
| GRADE | THICKNESS (in) |
MIN LONGITUDINAL AVERAGE ENERGY 1) (ft-lbs) |
MIN LONGITUDINAL INDIVIDUAL VALUE 1) (ft-lbs) |
ZONE 1 TEST TEMP | ZONE 2 TEST TEMP | ZONE 3 TEST TEMP |
|---|---|---|---|---|---|---|
| 50T | 0.1875 - 2.00 | 15 | 10 | 70 oF | 40 oF | 10 oF |
| 50T | 2.01 - 3.00 | 20 | 15 | 70 oF | 40 oF | 10 oF |
| 50F | 0.1875 - 2.00 | 25 | 20 | 70 oF | 40 oF | 10 oF |
| 50F | 2.01 - 3.00 | 30 | 24 | 70 oF | 40 oF | 10 oF |
| GRADE | THICKNESS (in) |
MIN LONGITUDINAL AVERAGE ENERGY 1) (ft-lbs) |
MIN LONGITUDINAL INDIVIDUAL VALUE 1) (ft-lbs) |
ZONE 1 TEST TEMP | ZONE 2 TEST TEMP | ZONE 3 TEST TEMP |
|---|
1) CVN impact testing in accordance with ASTM A673.
Please inquire for orders requiring CVN impact testing.
Chemical Composition
(Heat Analysis, wt. %, maximum unless noted)
Hide/Show specific columns EDIT
| TYPE | C 1) (MAX wt %) |
MN 1) (wt %) |
P (MAX wt %) |
S (MAX wt %) |
SI 2) (wt %) |
CU 3) (MIN wt %) |
V (wt %) |
CB (wt %) |
V+NB (wt %) |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 0.23 | 1.35 | 0.030 | 0.030 | 0.40 | 0.20 | - | 0.005 - 0.05 | - |
| 2 | 0.23 | 1.35 | 0.030 | 0.030 | 0.40 | 0.20 | 0.01 - 0.15 | - | - |
| 3 | 0.23 | 1.35 | 0.030 | 0.030 | 0.40 | 0.20 | 0.01 - 0.15 | 0.005 - 0.05 | 0.02 - 0.15 |
Hot Tags: astm a709 grade 50, China astm a709 grade 50 manufacturers, suppliers, factory, ASTM A53 GI Galvanized Steel Pipe, ASTM A53 Gr A Hot Rolled Galvanized Steel Pipe, EN10210 Hot Dip Galvanized Oil Drilling Pipe, Sch 40 80 Seamless Galvanized Steel Pipe, Q345B Galvanized Steel Pipe
