Overview of 0.5 x 1522 mm DC01 Cold Rolled Strip in Coils
DC01 cold rolled non-alloy steel strip is ordered here as a coil 0.5 mm thick and 1522 mm wide, close annealed and skin passed, which is what the CRCA and temper-passed description refers to. A thin gauge in a wide coil suits processors that slit, blank or roll form the strip on continuous lines and need the incoming coil to behave the same way from the first metre to the last. DC01 is the basic cold forming grade of the low carbon flat product family, so the strip is intended for bending, beading, light drawing and profiling rather than for structural load carrying.
What CRCA and Skin Passing Contribute
Cold rolling hardens low carbon steel, and annealing is used afterwards to restore ductility. Close annealing brings the coil through a controlled temperature cycle and cools it so that the ferrite structure recrystallises and the material becomes formable again. Fully annealed strip, however, can show yield point elongation, the condition that produces Luders bands or stretcher strains as visible lines on a formed surface. A skin pass, also called temper rolling, applies a very small final reduction that removes the discontinuous yielding, improves flatness and sets a defined surface roughness. The result is a strip that forms without strain markings and that accepts paint, lacquer or organic coating evenly.
Supply Condition at a Glance
| Grade | DC01 cold rolled non-alloy steel strip |
| Nominal thickness | 0.5 mm |
| Nominal width | 1522 mm |
| Condition | Cold rolled, close annealed, skin passed |
| Form of supply | Strip in coils, mill edge or trimmed as ordered |
| Surface | Skin-passed matte to slightly bright finish |
| Typical use | Roll forming, bending, beading, light drawing, coated panels |
Dimensions and tolerances for cold rolled uncoated flat products of low carbon steel are normally agreed against EN 10131 for thickness, width and flatness, while the grade itself is defined in EN 10130.
Which Standards Apply to DC01
DC01 comes from the European system for cold rolled low carbon flat products for cold forming. Older drawings often quote the superseded DIN 1623 designations St12 or FeP01; EN 10130 replaced that standard and DC01 replaced those names, so the two refer to the same general class of material. Equivalent commercial grades in other systems include SPCC under JIS G 3141 and CR1 under ISO 3574, while ASTM A1008 describes cold rolled carbon steel sheet of commercial quality. A purchase specification that names DC01 to EN 10130, together with a tolerance standard and a surface class, removes most ambiguity about what the coil should be.
Forming and Application Fit
Roll forming of profiles, cladding and sectioned components.
Bending, beading, coining and light drawing where a smooth surface matters.
Slitting and blanking ahead of further press or coating work.
Panel and casing parts that are painted or powder coated after forming.
Packaging and general fabrication needing thin, flat, uniform steel.
Because the skin pass raises surface quality and stabilises yielding, the strip is normally chosen when the visible surface of the finished part matters, and when the forming operation is light enough to sit within the basic grade ductility rather than needing a drawing grade.
Coil Handling, Storage and Traceability
Thin cold rolled coil keeps its flatness best when it is lifted with a proper coil grab or C-hook, stored on a saddle or pallet clear of the floor, and kept dry. Moisture between wraps is the usual reason for edge staining on thin gauge material, and it is avoided by keeping coils indoors, letting condensation evaporate before unwrapping, and using the oldest stock first. Each coil should stay identifiable so that the mill certificate, heat number and dimensional record can be matched to the parts produced from it.
Frequently Asked Questions
Q: What does CRCA mean?
CRCA stands for cold rolled close annealed. It describes strip that has been cold reduced and then annealed in a close or batch cycle to restore formability.
Q: Why is the coil skin passed after annealing?
Skin passing removes yield point elongation, improves flatness and sets surface roughness, which prevents strain marks during forming and helps coatings adhere evenly.
Q: Which standard defines DC01?
DC01 is defined in EN 10130 for cold rolled low carbon flat products for cold forming. St12 and FeP01 are older DIN 1623 designations that the current grade replaced.
Q: Can 0.5 mm DC01 strip be roll formed?
Yes. Thin skin-passed DC01 strip is widely roll formed and bent, provided the bend radius suits the thickness and the tooling does not over-strain the material.
Q: Is DC01 the same as SPCC?
They are close equivalents from different standards. DC01 sits in EN 10130 and commercial quality SPCC sits in JIS G 3141, so properties and tolerances should be compared when substituting one for the other.
Q: How should thin cold rolled coils be stored?
Indoors, dry, on saddles or pallets clear of the floor, using the oldest coils first so that the strip stays free of edge rust and moisture staining.

