1200x2440mm Carbon Steel Plate: S235JR, Q345, Q235, A36, DC01 Grades

Nov 06, 2025 Leave a message

The 1200 by 2440 millimeter carbon steel plate is one of the most commonly ordered sheet formats in the world, close to the classic 4 by 8 foot size used in many markets. The same dimension can be delivered in very different grades, from soft cold-rolled DC01 to structural S235JR, Q235, Q345 and A36, so the grade, not the size, decides what the plate can do. This guide compares the grades offered in this format and answers the practical processing questions that buyers ask about DC01 sheet in particular.

Grade Comparison at a Glance

Grade Standard Min yield (typical) Tensile range Typical use
DC01 EN 10130 130-260 MPa 270-410 MPa Stamping, bending, deep drawing of thin sheet
Q235 GB/T 700 235 MPa (up to 16 mm) 370-500 MPa General structures, frames, brackets
S235JR EN 10025-2 235 MPa (up to 16 mm) 360-510 MPa Structural steelwork, welded assemblies
Q345 GB/T 1591 345 MPa 470-630 MPa Heavier structures, bridges, machinery
A36 ASTM A36 250 MPa 400-550 MPa Structural plates, frames, general fabrication

The table shows why the same 1200 by 2440 plate can serve a stamped enclosure in one order and a load-bearing frame in the next: DC01 is a forming grade with low yield and high elongation, while Q345 and A36 are structural grades with much higher load capacity but lower formability.

DC01 in Focus: Composition and Mechanical Behavior

DC01 is the general forming grade of EN 10130, the European standard for cold-rolled low-carbon steel for cold forming. Its ladle analysis limits are carbon 0.12 percent, manganese 0.60 percent, phosphorus 0.045 percent and sulfur 0.045 percent maximum, which keeps the material soft and weldable. The yield strength range is 130 to 260 MPa and the tensile range is 270 to 410 MPa, with a minimum elongation A80 of 28 percent for common gauges. In hardness terms, DC01 is typically no harder than about 65 HRB, which is why it forms so readily. Its low yield-to-tensile ratio and high elongation make it stable in conventional cold bending: cracking is unlikely unless the bend radius is very tight or the forming speed is excessive, in which case micro-cracks can appear.

Cutting DC01 Sheet

DC01 sheet suits all common cutting methods. Laser cutting gives a clean edge, tight dimensional accuracy and is ideal for precision parts with complex profiles; it also minimizes heat-affected edge hardening when parameters are set correctly. Conventional shearing is the economical choice for large quantities of straight, standard-size cuts, and it is fast enough to keep up with high-volume production. For best edge quality with shearing, the blade clearance should match the sheet thickness, and heavy burrs should be removed before forming or painting.

Forming, Surface Treatment and Heat Treatment Options

Because DC01 is soft and ductile, it accepts ordinary surface treatments as well as wire drawing and coating processes that improve appearance and corrosion resistance. The bare cold-rolled surface is also a good base for phosphating and painting. For heat treatment, DC01 can be used to manufacture carburized and carbonitrided parts where only low core strength is required, such as mechanical components with modest hardness demands; the low carbon content keeps the core tough while the case is hardened. Plating, galvanizing or painting after forming is standard practice to protect the surface in service.

What Buyers Should Verify on Delivery

When ordering 1200 by 2440 DC01 sheet, confirm four items: the standard and grade, for example DC01 per EN 10130; the surface quality class, since EN 10130 distinguishes improved and normal surface quality for visible and hidden parts; the dimensional tolerances, which follow EN 10131 for cold-rolled sheet and strip; and the mechanical certificate, which should state yield, tensile and elongation values. Because the same size is available in several grades, the grade line on the order is the detail that prevents the most expensive mistakes.

Frequently Asked Questions

Q1. What is the density of DC01 steel?

7.85 g/cm³, equivalent to 7850 kg/m³, the standard density for low-carbon steel. It is used to convert sheet dimensions and thickness into weight for transport and cost calculations.

Q2. Is DC01 the same as SPCC or ST12?

They are close equivalents, not identical. DC01 per EN 10130, SPCC per JIS G3141 and ST12 per the older German material designation system share the same family of low-carbon cold-rolled sheet, with small differences in composition limits and property ranges. DC01 has stricter control of phosphorus and sulfur than some equivalents, which improves consistency.

Q3. Can DC01 sheet be welded?

Yes. Its low carbon content makes it one of the easiest steels to weld by conventional methods, with no preheat required for normal gauges. For painted or coated parts, protect the surface around the weld and repair the coating afterwards.

Q4. What is the difference between DC01 and DC02?

Both are defined in EN 10130. DC01 is the standard forming grade for ordinary stamping and simple bending, while DC02 offers deeper drawing capability for medium-complexity parts such as containers and automotive interior components, with tighter property control.

Q5. Will DC01 crack during cold bending?

Under normal conditions, no. Its high elongation and low yield strength allow stable bending at conventional radii. If the bend radius is too small relative to the thickness, or the material is worked below its minimum bending temperature, micro-cracks may develop, so the minimum bend radius from the supplier should be respected.