1mm SPCC and SPCD Coil with ASTM A792 AZ150 Aluminium-Zinc Coating

Jul 30, 2025 Leave a message

What SPCC and SPCD Mean on a Coil Order

SPCC and SPCD are grade designations in JIS G 3141, the Japanese standard for cold rolled steel sheet and strip. The letters read as steel, plate and cold rolled, and the final letter sets the forming quality, with C standing for commercial quality and D for drawing quality. In practice SPCC is the general purpose, low carbon, fully processed sheet used for bending, lock forming and light drawing, while SPCD is a drawing grade with controlled chemistry and higher elongation that survives deeper press work.

ASTM A792 and the AZ150 Coating Designation

ASTM A792 covers steel sheet coated by the hot dip process with an aluminium-zinc alloy containing about 55% aluminium, 43.4% zinc and 1.6% silicon. The alloy combines the barrier protection of aluminium with the sacrificial, galvanic protection of zinc, so cut edges and small scratches continue to be protected after the coating is breached. AZ150 is a coating mass designation meaning 150 g/m2 total over both surfaces, which is about 75 g/m2 per side and roughly 20 micrometres of coating thickness per side. Heavier classes such as AZ165 and AZ200 are chosen where the service environment is more aggressive.

Parameter Specification
Base steel grades SPCC and SPCD to JIS G 3141, with commercial, forming and structural grades also available under ASTM A792
Coating alloy Hot dip aluminium-zinc, approximately 55% Al, 43.4% Zn and 1.6% Si
Coating mass AZ150 150 g/m2 total, about 75 g/m2 per side, roughly 20 micrometres per side
Thickness range 0.30 mm to 1.20 mm, with 1.0 mm as a standard stock size
Width range 600 mm to 1250 mm, slit coil available from 30 mm
Surface Regular spangle, minimised spangle or skin passed smooth
Treatment Chromate passivation, chrome free passivation or thin acrylic, with optional light oil

Base Steel Properties Behind the Coating

The coating protects the surface, but the forming behaviour of a 1 mm coil comes from the base steel. Commercial quality SPCC is supplied with a tensile strength typically between 270 and 410 MPa and elongation above 28% at 80 mm gauge length, which suits roll forming, bending and lock seaming. Drawing quality SPCD is delivered with lower yield strength and elongation above 34%, so it can be pressed into appliance panels and deep housings without splitting. Certified figures for each coil are stated on the mill test certificate, and the equivalent bare grades in other systems are DC01 to EN 10130 and Q195 or Q215A to the Chinese standard.

Yield strength: low enough for tight bend radii, high enough to hold a formed shape.

Elongation: above 28% for SPCC and above 34% for SPCD at 80 mm gauge length.

Flatness and camber: controlled so that the strip tracks straight through roll formers and presses.

Coating adhesion: tested by bend and impact so that the alloy layer does not flake at the fold line.

Forming, Joining and Corrosion Performance

Aluminium-zinc coated coil bends and roll forms much like galvanised coil, but the harder alloy layer calls for slightly larger tool radii and for tooling that is kept clean to avoid score marks. Shearing and punching leave an exposed edge, and the sacrificial action of the coating protects roughly 1 to 2 mm of bare edge in normal outdoor exposure, which is why cut edges of roofing sheets do not need painting. Resistance welding is possible but demands higher electrode force and more frequent tip dressing than bare steel, and any weld or damaged area should be touched up with a repair coating to restore the barrier. Coil must be stored under cover on dry bearers, because trapped moisture between laps produces white rust.

Typical Applications for 1 mm AZ150 Coil

The combination of a 1 mm base and a 150 g/m2 aluminium-zinc coating is the default specification for roofing and wall cladding, purlins, agricultural buildings, industrial sheds, garage doors, HVAC casings and duct supports, cable trays, solar mounting rails, appliance side and back panels, and automotive underbody shields. Where the finished part will be colour coated, the same coil is supplied as the substrate for a paint line, with the passivation chosen to suit the primer system.

Frequently Asked Questions

Q: What does SPCC stand for?
SPCC stands for Steel Plate Cold rolled Commercial, a designation in JIS G 3141 for cold rolled carbon steel sheet and strip of commercial forming quality.

Q: What is the difference between SPCC and SPCD?
SPCC is commercial quality for bending and light forming, while SPCD is drawing quality with controlled chemistry, lower yield strength and higher elongation for deeper press work.

Q: How much coating is AZ150?
AZ150 is 150 g/m2 of aluminium-zinc alloy measured over both surfaces, about 75 g/m2 per side or roughly 20 micrometres of coating thickness per side.

Q: Does ASTM A792 cover the coating or the steel?
ASTM A792 is the product standard for steel sheet coated by the hot dip process with a 55% aluminium-zinc alloy, so it defines the coating, its mass and the coated product requirements together with the base metal.

Q: Can 1 mm aluminium-zinc coil be welded?
Yes, by resistance, arc and laser processes, but settings must be adjusted for the coating and welded areas repaired with a suitable coating.

Q: Why does the cut edge not rust quickly?
The aluminium-zinc alloy protects exposed edges galvanically, so a sheared edge is protected for roughly 1 to 2 mm before the coating's sacrificial capacity is exhausted.