Q235 Steel Coil: Mechanical Properties and Grade Selection Guide

Mar 05, 2026 Leave a message

Overview of Q235 Steel Coil

Q235 is a non-alloy carbon structural steel specified in GB/T 700. The designation Q235 means the steel guarantees a minimum yield strength of 235 MPa for thickness up to 16 mm. It is the most common carbon steel grade used in China for general structures, and it is supplied as hot-rolled coil, cold-rolled coil, plate, strip, bar and section. Because of its balanced strength, ductility and low cost, Q235 is the default choice for frames, brackets, housings, supports and lightly loaded structures.

Chemical Composition of Q235 (GB/T 700)

The composition limits for Q235 are set by GB/T 700. The following values are the maximum allowable product analysis percentages.

Grade C (%) Si (%) Mn (%) P (%) S (%)
Q235A 0.22 0.35 1.40 0.045 0.050
Q235B 0.20 0.35 1.40 0.045 0.045
Q235C 0.17 0.35 1.40 0.040 0.040
Q235D 0.17 0.35 1.40 0.035 0.035

Mechanical Properties of Q235

For thickness up to 16 mm, Q235 guarantees a yield strength of at least 235 MPa. The tensile strength range is 370 to 500 MPa, and the minimum elongation is 26% for products up to 40 mm thick. The Brinell hardness of Q235 is typically in the range of 100 to 130 HB, which gives it good machinability and stamping behavior for a structural carbon steel.

Impact Test Classes

Q235 is divided into four classes by impact testing temperature. Grade A has no impact requirement. Grade B requires a minimum Charpy V-notch impact energy of 27 J at room temperature (20 degrees Celsius). Grade C requires 27 J at 0 degrees Celsius, and Grade D requires 27 J at -20 degrees Celsius. The class should be selected according to the lowest service temperature of the structure.

Q235 vs Q195, Q215 and Q275

GB/T 700 covers the full family of carbon structural steels. Q195 offers a minimum yield of 195 MPa and higher elongation, making it easy to bend and suitable for light sections, wire and tube. Q215 is an intermediate grade with 215 MPa yield. Q235 is the general structural grade. Q275 provides a minimum yield of 275 MPa and a tensile range of 410 to 540 MPa, and is used where higher strength is needed with moderate cost. When strength demand is higher still, low-alloy grades such as Q355 (GB/T 1591) are used instead.

International Equivalents of Q235

Q235B is frequently compared with S235JR in EN 10025, which guarantees a yield of 235 MPa and similar tensile strength, and with ASTM A36, a common structural carbon steel in North America. These grades are not identical in every requirement, especially in impact testing and composition tolerances, so substitution should always be confirmed against the applicable standard and the end application. For tubing and piping, ASTM A53 and EN 10217 are among the standards used for welded carbon steel pipe made from similar base steels.

Selection Guidance for Buyers

When selecting Q235 coil or plate, confirm four points with the supplier: the impact class (A to D) required by your service temperature, the delivery condition such as hot-rolled or cold-rolled, the thickness and width tolerances applicable to the standard, and the mill test certificate with heat number. The certificate should list the grade, specification, chemical composition, mechanical properties, delivery condition and the applicable standard, and it must correspond one-to-one with the heat number of the supplied coil.

FAQ

What is the yield strength of Q235?

Q235 guarantees a minimum yield strength of 235 MPa for thickness up to 16 mm. The guaranteed value decreases slightly for thicker sections, as defined in GB/T 700.

What is the tensile strength range of Q235?

Q235 has a tensile strength range of 370 to 500 MPa, which satisfies the stress requirements of conventional structural applications.

What is the elongation of Q235?

The minimum elongation of Q235 is 26% for products up to 40 mm thick. The value provides good plasticity for cold bending and light stamping.

What is the difference between Q235A, Q235B, Q235C and Q235D?

The letters define the impact test requirement. Q235A has no impact requirement; Q235B requires 27 J at room temperature; Q235C requires 27 J at 0 degrees Celsius; Q235D requires 27 J at -20 degrees Celsius.

What is the hardness of Q235?

Q235 typically has a Brinell hardness of 100 to 130 HB, which gives moderate hardness with good machinability and stamping properties.

Is Q235 the same as S235JR or ASTM A36?

They are similar general-purpose structural carbon steels with comparable yield and tensile ranges, but they are defined by different standards with different tolerances and testing rules. Confirm the applicable standard and impact requirements before substitution.