What Is Black Annealed CRC Coil?
Black annealed CRC coil is a cold-rolled steel coil that has been annealed to soften it after cold rolling but has not been pickled or skin-passed afterwards. The term black describes the dark grey surface: during annealing in a bell-type furnace, the residual rolling oil on the strip carbonizes and forms a thin dark film on the surface. This film is not rust. It is a normal product condition for this route and provides a mild temporary protection, but the surface is not suitable for direct painting or plating without treatment. In the trade, black annealed coil is also called soft coil or annealed CRC, and it is the classic base material for galvanizing, tube making and deep drawing.
Production Route
The route is: hot-rolled strip, pickling to remove scale, cold rolling to the target gauge, then batch annealing in a bell-type furnace under a protective atmosphere, typically for many hours at temperatures around 650 to 720 degrees Celsius, followed by slow cooling. Annealing recrystallizes the cold-worked grain structure, restores ductility and lowers hardness so the strip can be deep drawn and formed without cracking. Because there is no subsequent temper rolling, the surface keeps the dark annealed appearance and the strip has a softer, more ductile condition than skin-passed material.
Grades: SPCC, DC01 and Q195
Black annealed CRC is commonly supplied in several equivalent low-carbon grades.
| Grade | Standard | Character | Typical use |
|---|---|---|---|
| SPCC | JIS G3141 | Commercial cold-rolled, tensile min 270 MPa | General stamping, bending, tubes |
| DC01 | EN 10130 | Cold forming, yield 140-280 MPa | General forming, drawn parts |
| Q195 | GB/T 700 | Low-carbon structural, yield min 195 MPa | Wire, light sections, tubes, fences |
The three grades sit at the same strength level and are often interchanged in trade, but each follows its own standard for composition and testing. The mill certificate states which standard applies.
Why Annealed Coil Is Preferred for Drawing and Tubing
Cold rolling hardens the steel through work hardening. If the strip is used directly, it is too hard for deep drawing and cracks easily at bends. Annealing restores elongation and lowers the yield point, so the strip can be drawn into shapes such as cups, battery shells, gas cylinders and radiator tanks, and can be roll-formed and welded into tube. The soft condition also gives more consistent forming behavior on high-speed presses, because the material has uniform low hardness.
Surface Condition and Handling
The black surface film should not be confused with mill scale. It is thin, and the surface is still smooth to the touch. For applications that need a clean bright surface, the coil can be pickled or processed further. The coil is usually supplied oiled to reduce rust risk. Storage matters: the dark surface shows moisture stains easily, so keep the coil in a dry warehouse, keep it off the floor, and protect the edges from damage. If the coil is to be deep drawn, check the oil film is present and uniform; dry or rusty edges can cause die wear and cracking.
Applications
Black annealed CRC coil is used for fuel tanks, tool boxes, drip pans, trailer siding, drawn housings, agricultural parts, welded tube and pipe, hose clamps, and countless small stampings. It is also the feedstock for electro-galvanizing and for hot-dip galvanizing lines where a soft, formable substrate is required. Because it is delivered soft, parts made from it can be formed in fewer operations than from skin-passed coil of the same grade.
Buying Checklist
When ordering black annealed CRC coil, confirm the grade and standard, thickness and width tolerances, the annealing batch and heat number, hardness or mechanical test values, oiling condition and packaging. Request the mill certificate and check that the heat number matches the delivered coil. For export, specify seaworthy packaging with rust-preventive paper, VCI protection and edge banding, because annealed surfaces are more sensitive to condensation during sea transit.
Frequently Asked Questions
Why is the coil surface black? The dark film comes from residual rolling oil carbonizing on the strip surface during bell-furnace annealing. It is a normal condition of this production route, not rust or scale.
What is the difference between black annealed and bright annealed coil? Black annealed coil is annealed without a final pickling or skin pass, keeping the dark carbonized film. Bright annealed coil is annealed in a clean atmosphere or pickled afterwards, giving a clean light surface. The mechanical softness is similar.
Is black annealed CRC coil suitable for deep drawing? Yes, this is its main purpose. Annealing restores ductility so the strip can be deep drawn; choose the grade and verify elongation on the certificate for the specific draw severity.
Can black annealed coil be painted directly? Not directly. The carbonized film and residual oil reduce paint adhesion, so the surface must be degreased and cleaned, and usually pickled or otherwise treated, before painting or plating.
What grades are typical for black annealed CRC? SPCC, DC01 and Q195 are the most common, sitting at the same low-carbon strength level. The choice follows the final standard required by your market and application.
Does the black film protect against rust? It gives only mild, short-term protection and should not be relied on. Coils are normally oiled, and the warehouse must be dry; for long storage or sea shipment, use VCI packaging.

