Classification of Cold-Rolled Steel Plate: Thickness, Material and Surface Treatment

Aug 22, 2025 Leave a message

Cold-rolled steel plate is produced by reducing hot-rolled coil at room temperature, which gives the product its characteristic combination of tight thickness tolerance, smooth surface and consistent mechanical properties. It is one of the most widely traded steel products, feeding automotive, appliance, construction and general machinery manufacturing. Because the term covers a wide range of grades, coatings and finishes, the product is normally classified along several independent axes that must be combined in a complete specification.

What Defines a Cold-Rolled Steel Plate

Cold rolling is a deformation process carried out below the recrystallisation temperature, followed by annealing and, where required, temper rolling or skin passing. The cold reduction work-hardens the steel, so the strip is annealed to restore ductility and is then given a light final pass to control flatness, surface roughness and yield-point elongation. Compared with hot-rolled product, cold-rolled plate offers better dimensional accuracy, a cleaner surface and higher strength at the same thickness, together with good formability and weldability. Thickness is the most important commercial difference: cold-rolled sheet and coil are normally supplied between about 0.2 mm and 3.0 mm, because cold reduction of heavier gauges becomes uneconomic.

Classification by Thickness

The familiar thin, medium and thick plate division, below 4 mm, 4 to 20 mm, and above 20 mm, describes plate in general rather than cold-rolled product specifically. Almost all cold-rolled material falls within the thin-sheet range, where further subdivisions are used commercially:

0.2 to 0.5 mm: packaging, closures and small electrical parts.

0.5 to 1.2 mm: appliance panels, automotive body panels and general fabrication.

1.2 to 3.0 mm: structural brackets, furniture frames, machine housings and tube making.

Above 3.0 mm: supplied only in limited widths; hot-rolled or hot-rolled pickled product is usually more economic.

Classification by Material

Four material families dominate the market. Ordinary carbon structural steel, such as the DC01 to DC04 drawing grades in EN 10130 or SPCC in JIS G3141, is used for general pressings, enclosures and building components. Low-alloy high-strength grades, including micro-alloyed and bake-hardening steels, offer higher yield strength at the same thickness, which allows down-gauging in load-bearing automotive and structural parts. Alloy structural steel is selected where through-hardening, wear resistance or a specific heat-treatment response is required. Stainless cold-rolled sheet, typically in the 304 and 430 families, is chosen for corrosion resistance in food processing, medical equipment and other hygiene-critical applications.

Classification by Surface Treatment

Uncoated cold-rolled sheet is supplied oiled or dry, with surface quality grades and finishes defined by the applicable standard, such as EN 10130 or ASTM A1008/A1008M. Coated product is classified by coating type:

Surface condition Coating or finish Typical end use
Uncoated Oiled or dry, matte or bright finish Pressings, enclosures, tube making
Hot-dip galvanized Zinc coating to EN 10346 or ASTM A653/A653M Construction, appliances, cable tray
Aluminium-zinc alloy coated Zinc-aluminium coating to ASTM A792/A792M Roofing, ducting, heat-exposed parts
Organic coated Coil-coated paint or laminated film Panels, white goods, building cladding

Grades and Supply Condition

Cold-rolled grades are chosen from the required forming severity rather than from strength alone. Drawing quality grades are specified for deep-formed parts, where the limiting properties are the forming limit curve and the plastic strain ratio, while structural and high-strength grades are specified where stiffness or yield strength drives the design. Thickness and width tolerances, flatness, edge condition and coil mass are defined in the dimensional standards and should be quoted explicitly, because a loose tolerance on a 0.4 mm product can exceed the thickness of the material itself.

How to Combine the Classifications

The classification axes are not alternatives; they are combined. A specification is complete only when the drawing quality or strength grade, the thickness and tolerance class, the surface finish and, where applicable, the coating type and coating mass are all stated. In practice the fastest route is to start from the forming operation: deep drawing demands a soft, interstitial-free grade with a controlled surface, while a simple bend or a roll-formed section is usually satisfied by a commercial quality or high-strength low-alloy grade.

FAQ

Q: Is cold-rolled steel the same as cold-rolled galvanized steel?
No. Galvanizing is a coating applied to a cold-rolled substrate and is standardised separately, so a galvanized specification must state the substrate grade and the coating mass in addition to the thickness.

Q: What thickness range is available in cold-rolled plate?
Most cold-rolled sheet and coil is supplied between about 0.2 mm and 3.0 mm. Above that range hot-rolled or hot-rolled pickled product is normally more economic.

Q: Does cold rolling make the steel stronger?
Yes, cold reduction work-hardens the steel, and the subsequent annealing step restores ductility. Final strength therefore depends on the delivery condition rather than on the rolling pass alone.

Q: What is the difference between DC01 and SPCC?
Both are commercial quality grades. DC01 is defined in EN 10130 and SPCC in JIS G3141; their properties are close and the choice usually follows the drawing standard used by the customer.

Q: Which surface treatment gives the best corrosion resistance?
The coating type and above all the coating mass determine corrosion resistance. A heavier zinc or zinc-aluminium coating delivers longer life than a change of substrate grade alone.

Q: Why is temper rolling used?
Temper rolling suppresses the yield-point elongation that would otherwise cause stretcher strains during forming, and it brings the surface roughness into the range required for painting.