Cold Rolled Steel Coil DC01 to DC06 and SPCC: Grades, Tempers and Applications

Sep 01, 2025 Leave a message

Overview: Cold Rolled Steel Coil in DC and SPCC Grades

Cold rolled steel coil in the DC01 to DC06 family and the SPCC designation is produced by cold reducing hot rolled substrate at room temperature, which makes the sheet thinner, flatter and smoother than hot rolled stock. The DC grades are defined in EN 10130, while SPCC is the commercial quality cold rolled sheet and strip designation of JIS G 3141. It is the standard feedstock for press work, roll forming and painted panel production.

Grade Comparison: DC01, DC02, DC03, DC04, DC05, DC06 and SPCC

Grade Standard Formability / character Typical use
DC01 EN 10130 General purpose forming Bending, roll forming, general panels
DC02 EN 10130 Drawing quality Moderate drawing work
DC03 EN 10130 Deep drawing quality Deeper drawn components
DC04 EN 10130 Deep drawing, carbon max 0.08 %, manganese max 0.40 % High forming requirements
DC05 EN 10130 Extra deep drawing quality Severe draws and complex shapes
DC06 EN 10130 Extra deep drawing, interstitial free type Most demanding press parts
SPCC JIS G 3141 Commercial quality sheet and strip, plate form only General press and sheet metal work

The numbering of the DC grades is a practical guide to forming severity: the higher the figure, the greater the drawability and the softer and more formable the annealed structure. A part that draws cleanly in DC04 may tear in DC01, so the grade should always be matched to the tool.

Rolling Tempers and Delivery Condition

Cold rolled sheet and strip are supplied in several conditions. Full hard material is rolled to the final gauge without annealing and represents a thickness reduction of about 50 %, which raises strength and hardness at the cost of ductility. Half hard and quarter hard conditions use progressively smaller reductions and sit between full hard and annealed stock. Skin rolled material receives a light final pass, typically around 0.5-1.5 % elongation, to remove the yield point elongation that would otherwise cause stretcher strains during forming, and to give the flat, paintable surface demanded by appliance and automotive panel work. ASTM A1008 is a widely used specification for cold rolled carbon steel sheet covering mild to high strength grades, and material made to it develops a high integrity surface that is normally oiled to protect against corrosion and ageing during storage.

Surface Finish, Dimensions and Tolerances

Surface: bright, smooth and free from scale, supplied dry or with a protective oil film.

Thickness: SPCC sheet metal stock is mostly distributed in the 0.5-3.2 mm band, with 1.6 mm and 2.0 mm being the most stable and widely held sizes.

Width and form: supplied as coil, slit strip or cut to length sheet, with edge condition specified as mill edge or trimmed edge.

Flatness and camber: controlled by tension levelling so that the coil feeds cleanly on high speed press and roll forming lines.

Mechanical properties: the cold reduction route gives a finer grain and a more uniform structure than hot rolled material, with higher strength and hardness for the same thickness.

Typical Applications

Automotive body and structural parts, brackets and inner panels.

Electrical appliances, cabinets and housings.

Steel office equipment and shelving.

Roll formed sections, cable trays and building profiles.

Base material for subsequent galvanizing, painting or coil coating.

Frequently Asked Questions

Q: What is the difference between SPCC and SGCC?
SPCC is uncoated cold rolled commercial quality sheet, while SGCC is hot dip galvanized. SGCC and other galvanized grades have good corrosion resistance because the zinc coating protects the steel, and SGCC is slightly stronger in this respect because the hot dip layer is thicker and more uniform. SPCC has poor corrosion resistance on its own and needs an additional anti-corrosion treatment in service.

Q: Which standard covers cold rolled steel?
ASTM A1008 is a standard specification for cold rolled carbon steel sheet that includes mild to high strength grades, and its material develops a high integrity surface that is usually oiled to prevent corrosion and ageing.

Q: What types of cold rolling condition are available?
Cold rolled sheet and strip come in full hard, half hard, quarter hard and skin rolled conditions. Full hard rolling reduces thickness by about 50 %, while the other conditions involve smaller reductions.

Q: What is SPCC cold rolled steel?
SPCC is a steel material for sheet metal and press work, supplied only as plate rather than long product. Most board thicknesses fall between 0.5 mm and 3.2 mm, with 1.6 mm and 2.0 mm the most stable distribution, and its smooth surface is why it is also called rolled material, cold material or polished material.

Q: Is there another name for cold rolled steel?
Cold formed steel, or CFS, is the common term for steel products shaped by cold working near room temperature, such as rolling, pressing, stamping and bending, and stock bars and sheets of cold rolled steel are widely used across manufacturing.

Q: Does the grade number affect forming?
Yes. Formability rises from DC01 through DC06, so the grade should match the draw depth and the risk of tearing or springback in the tool.