Three Layers Decide the Performance of a Corrugated Sheet
A colour-coated corrugated sheet is a composite product, and its performance is decided by three layers that must all be specified. The base is a cold-rolled steel substrate that provides the mechanical strength. On top of it sits a metallic coating, normally zinc applied by the continuous hot-dip process, which provides corrosion protection including at cut edges. Finally an organic paint system provides appearance, colour retention and additional barrier protection. A specification that states only the sheet thickness and the colour leaves two thirds of the product undefined.
Coil-coated flat product of this type is standardised in the continuously organic-coated steel standards, with the metallic coating and substrate taken from the continuous hot-dip coating standards; painted hot-dip coated sheet intended for exterior building products is covered by ASTM A755/A755M, and prepainted steel sheet and strip is also standardised in GB/T 12754. Roof and wall sheets formed from these coils are covered by self-supporting metal sheet standards such as EN 14782.
Substrate Thickness and What It Does Not Tell You
Corrugated sheet is most commonly formed from substrate between 0.3 mm and 0.8 mm. Thin gauges from 0.3 mm to 0.4 mm suit internal partitions, linings and temporary structures where loads are light. Gauges from 0.5 mm to 0.8 mm are used for roofs, external walls and large industrial buildings, and thicker substrate is needed as the span increases.
Thickness alone is a poor basis for comparison between suppliers. Two sheets of the same nominal gauge can differ in zinc coating mass and paint thickness by a factor of two, and it is the coating system, not the extra hundredth of a millimetre of steel, that decides how the sheet performs after five years on a coastal site. Buying decisions based on gauge alone are the main reason low-zinc sheets fail early.
Metallic Coating: The Number That Sets Corrosion Resistance
The metallic coating is designated by mass per unit area of the coated surface. In the continuous coating standards the designation is Z followed by the total coating mass on both surfaces in grams per square metre; in ASTM A653 the inch-pound designations G40, G60, G90 and G115 describe the same coating concept in ounces per square foot of total surface, so a G90 coating corresponds to approximately Z275.
| Zinc coating designation | Approximate inch-pound equivalent | Typical service environment |
|---|---|---|
| Z100 to Z140 | G40 to G60 | Interior and dry inland conditions, sheltered linings |
| Z180 | G60 | General inland external walls and roofs |
| Z275 | G90 | External roofing and cladding, moderate industrial exposure |
| Z350 and above | G115 and above | Coastal, high-humidity and heavier industrial exposure |
Two rules follow. First, choose the coating mass from the environment and the expected service life, not from the gauge: a thick sheet with a light coating will perforate at a cut edge long before a thinner sheet with a heavy coating. Second, confirm whether the coating is applied before or after profiling, because cut edges created after coating rely entirely on the coating's sacrificial action for protection.
Paint System Type and Dry Film Thickness
The organic coating is chosen for colour retention and for resistance to the specific environment. Polyester finishes are the general-purpose choice for inland and sheltered use. Silicon-modified polyester and polyurethane systems are used where UV exposure and chalking must be limited. Fluorocarbon systems are specified for long-life architectural and severely exposed façades. Laminate and plastisol systems give a much heavier film and are used where mechanical damage and aggressive atmospheres dominate.
Dry film thickness on the weather-exposed face is normally greater than on the reverse, because the reverse is protected by the building. Typical practice is a top coat of roughly 15 to 25 micrometres on the exposed face for normal environments, rising to about 20 to 25 micrometres or more with a more durable resin system for coastal and chemically aggressive sites, with a thinner primer and backing coat on the reverse. Adhesion is verified by the standard coil-coating test methods of the EN 13523 series, which cover film thickness, gloss and related film properties.
Profile Geometry: Overall Width Against Effective Cover Width
Corrugated and trapezoidal sheets are described by the overall width of the coil they are formed from and by the effective cover width of the finished sheet after the side laps are deducted. A sheet formed from a 1000 mm coil may give an effective cover of roughly 900 mm to 1000 mm depending on the profile, and a sheet formed from a 1200 mm coil commonly gives an effective cover near 1000 mm for trapezoidal profiles. Calculating the roof area from the overall width rather than the effective width is a frequent cause of a shortfall on site.
Profile choice must also follow span and load. Deep trapezoidal profiles with a high rib give much greater stiffness than shallow sinusoidal profiles at the same gauge, so long-span roofs should use a deep rib and a heavier substrate rather than a heavier gauge of a shallow profile. Rib height, pitch, stiffening ribs in the pan and the fixing position are all part of the sheet specification, together with the fastening type and the lap detail at the ends and sides.
Marking, Traceability and Identification
Every pack should carry a legible identification that ties the sheets to the coil they came from. The minimum data set is the substrate grade and standard, the metallic coating designation, the paint system type and film thickness, the substrate thickness and the profile designation, and the production date, together with the heat number and coil number for traceability. Where the project requires inspection documents, the document type is stated in the order and the certificate must reference the same heat and coating data.
Marking should survive the site. Inkjet or stencil marks on the reverse face, and a printed label on the pack, are normal; a mark placed only on the exposed face will be lost or will have to be cleaned off, and a mark placed only on the outer wrap will be lost as soon as the pack is opened. For cut-to-length sheets, mark the reverse face of each sheet or bundle at a consistent position so a partly consumed pack can still be identified.
Frequently Asked Questions
Q: What substrate thickness is normal for colour-coated corrugated sheet?
A: Most supply falls between 0.3 mm and 0.8 mm. Values of 0.3 to 0.4 mm suit internal and light-duty work; 0.5 to 0.8 mm is used for roofs and external walls, with heavier gauges for longer spans.
Q: Which zinc coating mass should be specified?
A: For dry inland and interior use, Z100 to Z180 is sufficient. For external roofs and walls in humid or moderately industrial areas, Z275 is the practical minimum, and for coastal or aggressive exposure Z350 or heavier should be selected.
Q: How thick should the paint film be?
A: Roughly 15 to 25 micrometres of dry film on the exposed face is typical practice for normal environments, with more where a durable resin system is specified for coastal or chemically aggressive exposure. The reverse face normally carries a thinner coat.
Q: What is the difference between overall width and effective width?
A: Overall width is the width of the finished sheet including the laps; effective cover width is what remains after the side laps are deducted. Roof areas must be calculated from the effective width, or the order will be short.
Q: Is a heavier gauge a substitute for a heavier coating?
A: No. A thicker sheet with a light coating will still perforate at cut edges and at fixing holes in a corrosive environment. Environment and expected service life, not gauge, should drive the coating mass.
Q: What has to appear in the identification marking?
A: At minimum the substrate grade and standard, the metallic coating designation, the paint system, the substrate thickness, the profile and the production date, plus the heat and coil number where traceability is required.
Q: Can colour-coated sheets be cut and drilled on site?
A: Yes, but every cut edge and drilled hole exposes steel, so swarf must be brushed off, the cut edge should be treated with a compatible repair material where the exposure is severe, and sheets should not be walked on with dirty boots during installation.

