What a Customized Size Cold Rolled Steel Coil Covers
Cold rolled steel coil is not limited to a handful of catalogue sizes. Mills and processors routinely supply customized widths and thicknesses, including the commonly requested combinations 0.6 mm x 1000 mm, 0.75 mm x 1200 mm and 0.8 mm x 1500 mm. A customized coil order fixes five things at once: the substrate grade, the thickness, the width, the coil inner diameter and the coil weight. Each of those parameters influences formability, tooling compatibility and the price per ton, so they should be written on the enquiry together rather than agreed one by one afterwards.
Typical Size Range and Tolerances
| Parameter | Common range | Notes |
|---|---|---|
| Thickness | 0.3–3.0 mm | Below 0.5 mm needs careful tension control during rolling and slitting |
| Width | 600, 1000, 1200, 1250, 1500 mm | Intermediate widths produced by slitting from a master coil |
| Coil inner diameter | 508 mm or 610 mm | Must match the decoiler mandrel on the customer's line |
| Coil outer diameter | Up to about 1800 mm | Limited by coil weight and handling equipment |
| Coil weight | 3–8 t typical, up to 15 t on request | Lighter coils suit small presses and manual handling |
| Edge condition | Mill edge or slit edge | Slit edge is required when the width is not a mill rolling width |
| Thickness tolerance | Per EN 10131 or JIS G3141 | Tolerance class must be stated because it drives yield and cost |
Combinations such as 0.6 mm x 1000 mm are usually produced by slitting a wider master coil, which means the width tolerance and burr height depend on the slitting line rather than on the rolling mill. Where the coil feeds a roll forming line, the camber and the edge straightness matter as much as the width itself.
Grades Supplied in Customized Coil
DC01 (EN 10130): commercial-quality low carbon steel for bending, coining, beading and light drawing; formerly designated St12 or FeP01.
DC03 (EN 10130): drawing quality with tighter chemistry and higher elongation, used where the part needs deeper drawing or difficult profiling.
DC04 (EN 10130): deep-drawing quality with excellent formability under all types of deformation, for high forming requirements.
SPCC (JIS G3141): the Japanese commercial-quality equivalent, widely used for general presswork and enclosures.
SPCC-SD: the skin-passed dull finish variant of SPCC, preferred where the surface has to accept paint.
Enquiries sometimes quote a DC02 grade. The current EN 10130 series runs DC01, DC03, DC04, DC05 and DC06, so where DC02 appears on a drawing the controlling standard edition and the actual forming duty should be agreed before the coil is rolled; in most cases the requirement resolves to DC01 or DC03.
What Drives the Price Per Ton
Grade: DC04 and DC05 carry a premium over DC01 because of tighter chemistry and additional processing.
Thickness: very thin gauges increase rolling and handling cost per ton; very thick gauges reduce the number of meters per coil.
Width and slitting: non-standard widths generate slitting scrap and reduce the usable yield from the master coil.
Coil weight: small coils cost more per ton because of handling and packaging effort.
Surface and oiling: special finishes, dry coil or heavy oiling change the finishing route.
Quantity and delivery: full mill lots are cheaper per ton than small mixed-width lots.
Ordering Checklist and Incoming Inspection
State grade, standard and edition, for example DC01 to EN 10130.
State thickness and width with the tolerance class, not just the nominal figure.
State coil inner diameter, target coil weight and maximum outer diameter.
State the surface finish, oiling condition and edge type.
On receipt, verify coil weight and dimensions, check the mill certificate against the ordered grade, and inspect the first metre for rust, edge burrs, camber and surface defects before loading the decoiler.
FAQ
Q: Can cold rolled steel coil be supplied in a customized width?
Yes. Widths that are not standard mill rolling widths are produced by slitting a wider master coil, which allows almost any width between the minimum and maximum slitting limits to be supplied.
Q: What does the size notation 0.6 x 1000 mm mean?
It means 0.6 mm nominal thickness and 1000 mm nominal width. The ordered tolerance class decides how much the actual thickness and width may vary from those nominal figures.
Q: Which standard covers the thickness tolerance of cold rolled coil?
EN 10131 defines thickness, width, length and flatness tolerances for cold rolled low carbon flat products, and JIS G3141 defines tolerances for the Japanese SPCC series. The applicable standard should be named on the order.
Q: What coil inner diameter is standard?
508 mm and 610 mm are the two common inner diameters. The correct value is the one that fits the customer's decoiler mandrel, so it must always be confirmed at enquiry stage.
Q: Does coil weight affect the price per ton?
Yes. Small or split coils require more handling, strapping and packaging per ton, so the price per ton rises as the coil weight falls.
Q: What is the difference between mill edge and slit edge?
Mill edge is the original rolled edge of the strip, while slit edge is a cut edge produced by a slitting line. Slit edge gives an exact width but introduces a small burr that should be controlled for exposed or coated applications.

