DC01 and SPHC: Two Standards, Two Product States
DC01 comes from EN 10130 and describes cold-rolled, commercial-quality low-carbon steel intended for cold forming. SPHC is the commercial-quality hot-rolled steel plate, sheet and strip grade of JIS G 3131. The two names are often quoted together because DC01 is the reference point buyers use for formability and surface quality, while SPHC is what is actually purchased for heavier, less critical parts. They are not interchangeable products: one has been cold reduced, annealed and temper rolled, the other has been hot rolled and coiled straight from the finishing stands.
Understanding the difference is the fastest way to avoid over-specifying a job. A bracket that will be welded into a frame rarely needs a cold-rolled surface, and a visible painted panel rarely tolerates the surface and tolerance of hot-rolled stock.
DC01 Equivalent Materials Across Standards
| Designation | Standard | Notes |
|---|---|---|
| DC01 | EN 10130 | Current European cold-rolled commercial-quality forming grade |
| 1.0330 | EN material number | Numeric designation used alongside the DC01 symbol |
| St12 | DIN 1623 | Withdrawn designation, replaced by DC01 |
| CR4 | British trade designation | Common reference name for cold-rolled commercial mild steel |
| SPCC | JIS G 3141 | Japanese cold-reduced commercial-quality grade |
| Q195 / Q215A | Chinese cold-rolled grades | Comparable carbon and strength band |
One historical point matters when reading older drawings: DIN 1623 has been replaced by EN 10130, and the designation St12 has been replaced by DC01. A part specified as St12 should therefore be re-read as DC01 unless the drawing calls up a different replacement grade.
What SPHC Hot Rolled Coil Offers
SPHC is supplied in the hot-rolled condition with a mill-scale surface. Because it is not cold reduced, it is economical at heavier gauges, where cold rolling would demand very large reductions and a much higher price. Its advantages and limitations are both consequences of that route.
Thickness - available from light hot-rolled gauges upward, and strongest where heavier sections are needed.
Surface - mill scale, oxide and a rougher finish; normally pickled or blasted before painting.
Tolerance - wider than cold-rolled product, which is acceptable for structural and general engineering use.
Formability - adequate for bending, roll forming and welding, but not intended for severe drawing.
Cost - lower per tonne than cold-rolled coil at equivalent thickness.
For building work, SPHC is typically formed into purlins, girts, decking profiles and general structural members, then protected by painting, galvanizing or a powder coating.
Hot Rolled or Cold Rolled: How to Choose
| Factor | Hot rolled, such as SPHC | Cold rolled, such as DC01 or SPCC |
|---|---|---|
| Surface | Mill scale, rougher | Smooth, uniform |
| Thickness tolerance | Wider | Tight |
| Forming severity | Bending and roll forming | Bending and shallow drawing |
| Paint appearance | Requires surface preparation | Readily painted |
| Typical use | Frames, purlins, structural parts | Panels, housings, visible parts |
Where appearance and dimensional accuracy drive the design, cold-rolled material earns its higher price. Where the part is structural, welded and painted, hot-rolled material delivers the same function at lower cost.
Fabrication and Industrial Building Applications
Purlins, girts and secondary framing in industrial sheds and warehouses.
Floor decking and roof decking profiles.
Support brackets, base plates and general fabrication work.
Equipment frames, guards and machinery housings.
Racking, shelving uprights and storage structures.
Welding is straightforward on both product states, although the mill scale on hot-rolled stock should be removed locally before welding and before any protective coating is applied. Formed parts should be cleaned and coated promptly after fabrication, because bare low-carbon steel will begin to rust as soon as it is exposed to moisture.
Frequently Asked Questions
Q: What is DC01 material equivalent to?
DC01 corresponds broadly to the withdrawn German grade St12 under DIN 1623, to the British trade designation CR4, to SPCC under JIS G 3141, and to Chinese cold-rolled grades Q195 and Q215A. Its EN material number is 1.0330.
Q: Is DC01 the same as CR4?
DC01 and CR4 are two names for broadly the same commercial-quality cold-rolled mild steel, one from the European standard and one a British trade designation. Tolerances and chemistry limits still follow the standard named on the order.
Q: Is SPHC a cold-rolled or hot-rolled product?
SPHC is hot rolled. It is defined in JIS G 3131 as commercial-quality hot-rolled steel plate, sheet and strip, and it is supplied with a mill-scale surface rather than the smooth, temper-rolled surface of DC01 or SPCC.
Q: Can SPHC replace DC01 in a formed part?
Only where the forming is mild and surface appearance is not critical. SPHC has a rougher surface and wider tolerance, so a visible panel or a part with a tight draw should stay on cold-rolled material.
Q: Why is St12 still written on old drawings?
St12 was the German designation under DIN 1623. That standard was replaced by EN 10130 and the designation by DC01, so drawings are normally re-issued with the current grade while the old name remains in circulation.
Q: How should hot-rolled coil be stored before fabrication?
Keep coils under cover, off the ground and clear of standing water. Hot-rolled stock with mill scale is more tolerant of short exposure than cold-rolled sheet, but edges and cut faces will still rust if they stay wet.

