DC04 Galvanized Coil: Base Steel and Zinc Coating
DC04 galvanized steel coil is a two-part product: a deep drawing cold rolled base steel and a zinc coating applied after cold rolling. Understanding which part the order refers to prevents most specification disputes.
DC04 is the base grade. It is an unalloyed cold rolled low carbon steel to EN 10130 with material number 1.0338, tensile strength of 270-350 MPa and elongation A80 of at least 38%, which makes it suitable for deep drawn parts.
GI means hot-dip galvanized, where the strip passes through a molten zinc bath and the coating bonds metallurgically to the surface. It gives the thickest coating and the strongest sacrificial protection.
Electro-galvanized coil carries a thinner, very uniform coating and keeps the smoothest surface for painting.
CRC and HRC describe the substrate route, not the coating. CRC is cold rolled coil, the material actually used for DC04 because cold reduction plus annealing deliver the flatness and forming properties required. HRC is hot rolled coil, which is thicker, rougher and used only when a hot-dip coated structural product is intended.
Mixing these labels is common in enquiries: a request for DC04 CRC GI coil asks for deep drawing grade cold rolled base with a hot-dip zinc coating, and the drawing grade of the coated product must be confirmed against the coating standard.
Standards and Grade Mapping
The base steel and the coated product are governed by different standards, so a complete specification names both.
| Scope | Standard | Designation to order |
|---|---|---|
| Base steel, cold rolled for deep drawing | EN 10130 | DC04, material 1.0338 |
| Hot-dip zinc coated flat product | EN 10346 | DX54D+Z for DC04-level drawability |
| Electrolytically zinc coated flat product | EN 10152 | DC04+ZE |
| Hot-dip zinc coated steel sheet, American system | ASTM A653 / A653M | Deep drawing quality, zinc coated |
| Hot-dip zinc coated steel sheet, Japanese system | JIS G3302 | SGCD2 |
| Hot-dip zinc coated steel sheet, Chinese system | GB/T 2518 | Deep drawing coated grades |
| Structural steel for coated profiles | GB/T 700 | Q235B |
Choice follows the part, not the price list. Deep drawn housings need the drawability of DC04 or its coated equivalents. Structural frames, purlins and general fabrication are better served by a Q235B base with a zinc coating, because they need strength rather than drawability.
Zinc Coating Mass and Corrosion Performance
Coating weight is designated by the total mass of zinc on both surfaces, expressed in grams per square metre. Because zinc has a density of about 7.14 grams per cubic centimetre, the coating thickness per side follows directly from the designation.
| Coating designation | Total zinc mass | Approximate thickness per side | Typical exposure |
|---|---|---|---|
| Z100 | 100 g per square metre | about 7 micrometres | Indoor and light duty |
| Z140 | 140 g per square metre | about 10 micrometres | Indoor, occasional condensation |
| Z275 | 275 g per square metre | about 19 micrometres | Outdoor and industrial duty |
| Z350 | 350 g per square metre | about 24 micrometres | Severe and coastal duty |
Zinc protects in two ways. It forms a barrier that seals the steel from moisture and oxygen, and it corrodes preferentially at cut edges and scratches, which is what keeps a sheared edge from rusting as quickly as the exposed steel would. A heavier coating buys service life, but it also stiffens the surface and can flake at tight bend radii, so coating mass has to match both the environment and the forming severity. Alloy coatings such as zinc-iron, zinc-aluminium and aluminium-zinc use their own letter codes in the same standard and behave differently under forming and welding.
Surface Quality and Surface Treatment Codes
Coated coil is ordered with a surface quality and a surface treatment code. The quality class controls cosmetic freedom, and the treatment code controls corrosion protection during transport, storage and pressing.
| Surface quality | Description |
|---|---|
| A | High quality surface for visible parts |
| B | General quality surface for non-visible parts |
| C | Standard surface, where appearance is secondary |
| Code | Treatment | Purpose |
|---|---|---|
| O | Oiling | Temporary protection against oxidation |
| P | Phosphating | Improved paint adhesion and corrosion resistance |
| C | Chemical passivation | Reduced white rust formation in storage |
| PO | Phosphating and oiling | Combined press lubrication and protection |
| CO | Passivation and oiling | Storage protection with lubrication |
| PCO | Phosphating, passivation and oiling | Maximum combined protection |
| S | Organic sealing | Anti-fingerprint and handling protection |
| U | Untreated | For immediate in-line processing |
The treatment choice is not cosmetic. Phosphate layers improve paint adhesion but change die friction, and a heavy oil film can cause weld porosity in a resistance welding line. Treatment has to be selected together with the joining and painting process downstream.
Forming, Welding and Painting of DC04 Coated Coil
Deep drawing of coated coil introduces two effects that do not appear with bare steel:
Friction rises because the zinc layer is softer than the steel and can smear onto the die. Lubricant selection and die surface finish matter more than in uncoated forming.
Coating adhesion depends on the forming radius. Tight radii thin the coating locally, so bend radius and coating mass must be considered together.
Resistance spot welding of zinc coated sheet requires higher electrode force and current than bare steel, and electrode life is shorter because the zinc alloys with the copper electrode tips. Painting follows the usual sequence of cleaning, conversion coating and primer, and DC04 provides the flat, uniform substrate that keeps visible panels free from waviness after drawing. Cut edges remain protected by the sacrificial action of the coating, which is why coated deep drawn parts are widely used in automotive structures, appliance housings and construction components.
FAQ
Q: What is DC04 galvanized steel coil?
It is a deep drawing grade cold rolled steel to EN 10130 with material number 1.0338, supplied with a zinc coating applied either by hot-dip galvanizing to EN 10346 or electrolytically to EN 10152.
Q: What does GI mean compared with CRC and HRC?
GI means hot-dip galvanized and describes the coating. CRC means cold rolled coil and HRC means hot rolled coil, which describe the substrate route. DC04 is a cold rolled grade, so the base is CRC.
Q: How much zinc is on a Z275 coating?
Z275 designates 275 grams of zinc per square metre of sheet, counting both surfaces. At a zinc density of about 7.14 grams per cubic centimetre that is roughly 19 micrometres of coating per side.
Q: Which grades match DC04 in other standards?
DX54D+Z to EN 10346 gives the same drawability in a hot-dip coated product, SGCD2 in JIS G3302 covers the Japanese system, and deep drawing quality zinc coated sheet to ASTM A653 / A653M covers the American system.
Q: What is the difference between DC04 and Q235B coated coil?
DC04 is designed for deep drawing with lower tensile strength and high elongation. Q235B to GB/T 700 is a structural steel for frames and profiles where load capacity matters more than formability.
Q: Which surface treatment should be chosen for coated coil?
Oiling suits parts pressed soon after delivery, passivation and phosphating suit longer storage or painted parts, and organic sealing suits visible parts that must resist handling marks.

