DC04 Super Deep Drawing Cold Rolled CRC Steel Coil for Building Products

May 09, 2025 Leave a message

What a DC04 Super Deep Drawing Coil Delivers

DC04 is the deep drawing quality grade of the cold rolled low carbon family. In a building-products press shop it is the workhorse behind cable trays, duct sections, door skins, shelving uprights, lighting housings and profiled cladding accessories, because it combines a very clean, soft ferrite with enough strength to keep a formed part rigid in service. A super deep drawing coil is ordered when the drawn depth approaches the limit of what DC04 can carry, so that the corner radii, the draw ratio and the blank-holder setting all sit comfortably inside the forming window instead of at its edge.

Trade listings for this product sometimes use the spelling SPCEN or the abbreviation CRC. CRC simply means cold rolled coil, and the designation that actually governs the delivered properties is DC04 together with the material number 1.0338, so any quotation should reference the grade and the applicable product standard rather than the shorthand alone.

Reading the Designation and the Applicable Standards

DC04 is defined as a cold rolled low carbon steel for cold forming in EN 10130, with dimensional tolerances to EN 10131. The closest Japanese line is the SPCE deep drawing quality of JIS G 3141, which many drawings produced in Asia cite in parallel, while GB/T 5213 covers the same grade family for the Chinese market. Material number 1.0338 identifies the same steel in the European numbering system.

Designation used Meaning
DC04 Deep drawing quality cold rolled low carbon steel, EN 10130
1.0338 European material number for DC04
SPCE (JIS G 3141) Japanese deep drawing quality line, commonly cross-referenced
CRC Cold rolled coil, describing the supply format rather than the grade

Chemistry and Mechanical Properties

DC04 is fully aluminium-killed and fully processed, so the carbon and nitrogen that remain in solution are tied up by the aluminium addition and the sheet does not age in storage. Sulphur and phosphorus are held low because both form inclusions or solute hardening that would begin a tear in a deep draw.

Item Typical value
C, max 0.08 %
Mn, max 0.40 %
P, max 0.025 %
S, max 0.025 %
Al, min 0.015 %
Yield strength Re 210 MPa max
Tensile strength Rm 270 - 350 MPa
Elongation A80 36 % min
Plastic strain ratio r90 1.6 min
Work hardening exponent n90 0.18 min

Where a drawing operation needs more margin than DC04 can provide, DC05 raises the r-value and the work hardening exponent at a slightly lower yield strength, and DC06 lifts them again for the most severe draws. The choice is normally made by working backwards from the draw ratio of the deepest part on the drawing rather than from the strength of the finished component.

Surface Finish and the CRC Coil Format

Coil for building products is normally ordered with a matte or improved matte finish and a controlled skin pass, which prevents the yield-point elongation markings that would otherwise show through a thin paint film on a visible facade component. Tolerances for thickness, width and flatness follow EN 10131, with tighter thickness tolerance available for high-speed roll forming lines where a variation in section would show up as a wave in the finished profile.

Thickness range for the grade is conventionally quoted from about 0.3 mm to 2.0 mm, with the most common building-product sizes between 0.4 mm and 1.2 mm.

Coil is supplied in standard widths and slit to customer width, on 508 mm or 610 mm bores, with coil weights arranged to match the capacity of the customer's decoiler.

Surface condition is inspected coil by coil; scratch-free faces are specified where the part will be painted without a filling primer.

Both edges are trimmed square and burr-controlled so that roll forming stands and press feeds are not damaged.

Where DC04 Cold Rolled Coil Is Used in Building Products

Cold rolled DC04 is a substrate and a structural skin rather than a weathering surface. It is used indoors or behind a coating system, and the coating choice is usually made separately from the steel grade.

HVAC ducting, plenum sections and air-handling housings.

Cable management trays, trunking and support brackets.

Door frames, door skins and lift cabin panels.

Shelving, racking uprights and storage cabinet bodies.

Lighting reflectors, diffuser frames and electrical enclosures.

Roll-formed profiles and trim that are subsequently powder coated or painted.

For components exposed to weather, the same forming route is followed with a zinc or 55% aluminium-zinc coated substrate, using the coated grade designation of the corresponding drawing quality instead of uncoated DC04.

Frequently Asked Questions

Q: Does DC04 have a minimum or maximum yield strength?
The grade is controlled from above, with an upper limit of 210 MPa typical, because a low yield point is what allows the material to flow into a deep draw. There is no contractual minimum, only the natural scatter of an annealed product.

Q: Can DC04 be used outdoors without a coating?
No. Uncoated cold rolled steel rusts quickly in a wet environment, so exterior parts are always made from a coated substrate, a painted assembly or a different material family.

Q: What does CRC mean on a quotation?
CRC is shorthand for cold rolled coil and describes the supply format. It does not identify the grade, so the enquiry should always state DC04 or the material number 1.0338 as well.

Q: How is DC04 different from DC05?
DC05 is the next step up the drawing ladder, with a higher plastic strain ratio and work hardening exponent and a slightly lower maximum yield strength, which makes it the safer choice for the deepest draws in a building-product range.

Q: Is a skin pass always required?
For any part that will be visible after painting, yes. Without a light temper pass the sheet can develop yield-point elongation bands, which appear as visible surface markings on a flat panel or a shallow draw.

Q: Can DC04 replace DC03 without changing the press settings?
Usually yes, because DC04 is the more formable grade and will run with equal or lower blank-holder force. Where a part is running at the very edge of the tooling window, the change is worth validating with a trial coil before a full production order is released.