DC05 Quality Control Key Points

Aug 08, 2025 Leave a message

 

DC05 Cold-Rolled Steel Plate Quality Control Key Points
1. Raw Material Control
Chemical Composition Verification:

Key monitoring: C ≤ 0.06%, Mn ≤ 0.40%, P ≤ 0.025%, S ≤ 0.025%

Al content ≥ 0.015% (to ensure effective deoxidation)

Material report required for each batch (heat number tracking)

Bill Quality:

Surface quality of continuous casting billets inspected (no cracks or slag inclusions)

Control of non-metallic inclusion levels (Class B ≤ Grade 1.5, Class D ≤ Grade 1.0)

2. Production Process Control
Cold Rolling Process:

Rolling force control (to avoid edge wavy)

Thickness tolerance control (±0.03mm, ±0.02mm required for high-end applications)

Surface roughness Ra 0.5-1.6μm (adjustable depending on application)

Annealing Process:

Continuous annealing temperature 700-850°C (to ensure complete recrystallization)

Shielding gas purity (H₂ ≤ 5%, dew point ≤ -40°C)

Controlled cooling rate (to avoid age hardening)

3. Key Performance Testing
Test Item Standard Method Acceptance Criteria Frequency
Tensile Properties ISO 6892-1 Rm: 250-360MPa, A80 ≥ 38% (at the beginning and end of each coil)
Hardness ISO 6507-1 (HV) 80-120HV (5 points per batch)
Cupping Test ISO 20482 IE ≥ 9.0mm (every 500 meters)
r Value/n Value ISO 10113 r ≥ 1.6, n ≥ 0.20 (every batch)
Surface Quality EN 10130 No scratches or roller marks. 100% visual inspection
4. Surface Quality Control
Defect Type Monitoring:

Unacceptable Defects: Holes, Scars, Oxide Scale

Minor Permissible Defects: Minor Roller Marks (≤3/roll, ≤20mm in length)

Cleanliness Requirements:

Residual Oil ≤50mg/m² (Electroplating Grade Requirement ≤20mg/m²)

Ash Content Test (≤10mg/m²)

5. Dimensional Accuracy Control
Thickness Tolerance:

Conventional Grade: ±0.05mm

Precision Grade: ±0.03mm (Required for Automotive Exterior Panels)

Pattern Shape Control:

Straightness ≤3I units (≤1.5I for high-end applications)

Edge Thinning ≤5% of Nominal Thickness

6. Packaging, Storage, and Transportation Specifications
Rust-proof packaging:

VCI anti-rust paper + PE film (storage period ≤ 6 months)

Desiccant required for sea transportation (humidity ≤ 40% RH)

Stacking requirements:

Maximum stack height ≤ 3 meters (to avoid deformation)

Storage temperature 10-40°C, relative humidity ≤ 60%

7. Application-side quality control
Stamping verification:

Mesh analysis of first part (limiting drawing ratio ≥ 2.0)

Monitor for cracking and wrinkling defects (die gap adjustment)

Welding evaluation:

Spot welding parameter verification (electrode pressure 2-4 kN, current 8-10 kA)

Check weld nugget diameter ≥ 4√t (t is plate thickness)

8. Solutions for Common Problems
Surface Streaks:

Check roll finish (Ra must be consistent)

Adjust rolling oil filtration system (particle size ≤ 5μm)

Stamping Cracking:

Recheck r-value (if below 1.4, replace batch)

Check die R-angle (recommended ≥ 8t)

Aging Deformation:

Control inventory cycle (recommended ≤ 3 months)

Perform temper rolling (elongation 0.5-1.2%) as necessary

Note: High-end applications such as automotive exterior panels require the following:

Electronic scanning of non-metallic inclusions (SEM analysis)

Texture testing (gamma fiber texture ≥ 75%)

Full-width surface profilometer scanning (avoid micro-ripples)

DC05