Temperature Limits of the Passivation Layer on Galvanized Coil

Nov 06, 2025 Leave a message

What the Passivation Layer Actually Does

Passivation is the final chemical treatment applied to a galvanized coil after the zinc coating has solidified. Its purpose is to form a thin conversion film that limits the formation of white rust during storage and transport, and that provides a stable surface for subsequent painting or forming. That film is only tens of nanometres thick, which is exactly why it has a limited thermal budget.

Two families are in common use: traditional chromate passivation, and chromium-free systems based on silicate, acrylic resin or titanium and zirconium chemistry. Their temperature behaviour differs substantially.

Chromate Passivation at High Temperature

Above roughly 70 degrees C the water of crystallisation inside the film begins to be released, and the film starts to crack as it dehydrates.

As temperature rises further, the film decomposes irreversibly and loses its ability to isolate corrosive media from the zinc surface.

Visually the film turns yellow, brown or even black as oxidation proceeds, and the original metallic lustre disappears.

Chromate passivation is therefore a room-temperature technology. It should not be relied on where the coil will be heated during downstream processing or service.

Temperature Limits of Chromium-Free Passivation

System Typical limit Reason
Silicate based Generally above 100 degrees C Inorganic network structure gives relatively high thermal stability
Titanium / zirconium based Around 90 degrees C Mixed organic-inorganic structure of moderate stability
Acrylic resin based Usually not above 80 degrees C Organic resin softens and decomposes when hot

Overall, chromium-free films tolerate roughly 80 to 120 degrees C depending on formulation. Even the best of them is not a high-temperature coating: heat causes organic constituents to volatilise or decompose and leaves a porous, damaged film, so protective performance falls sharply once the limit is exceeded.

Why Passivation Films Fail When Heated

Composition: both chromate and chromium-free films contain moisture, organic matter or specific crystalline structures that become unstable when hot.

Thermal expansion mismatch: the film and the underlying zinc layer are different materials with different expansion coefficients. Temperature change creates internal stress, and the film cracks and peels.

Zinc reactivity: heat accelerates zinc oxidation, so once the film is breached the exposed zinc reacts quickly with oxygen and loses its protective role.

Higher-Temperature Alternatives

Where the application genuinely involves elevated temperature, the coating system rather than the passivation film has to be changed.

Product Bath composition Temperature capability Notes
Aluminised zinc coil Aluminium and silicon added to the zinc bath, for example 55% Al-Zn Long-term service around 315 degrees C, short-term exposure up to 650 degrees C Aluminium oxide surface film is very stable; first choice for high-temperature service
Zinc-aluminium-magnesium coil Aluminium and magnesium added to the molten zinc Generally around 200 degrees C Better than plain galvanizing, but below aluminised zinc; confirm exact figures with the producer
Plain galvanized coil Zinc only Passivation film limits practical use to near room temperature Suitable for ambient indoor and outdoor construction

Practical Selection Guidance

Keep chromate-passivated coil at ambient temperature through slitting, forming, storage and installation.

If a drying or curing oven follows the coil line, verify the peak metal temperature against the passivation type before scheduling the run.

For continuous service above about 200 degrees C, move to an aluminium-bearing coating rather than trying to upgrade the passivation film.

State the maximum service temperature in the enquiry so that the coating system, not just the passivation treatment, is selected correctly.

Frequently Asked Questions

Q: At what temperature does chromate passivation start to fail?
Degradation begins above roughly 70 degrees C, when water of crystallisation is released and the film begins to crack. Higher temperatures cause irreversible decomposition.

Q: Is chromium-free passivation more heat resistant than chromate?
Yes, generally. Chromium-free films tolerate roughly 80 to 120 degrees C, but the exact limit depends on whether the formulation is silicate, acrylic or titanium and zirconium based.

Q: Which chromium-free system is best for heat?
Silicate systems are the most heat resistant, typically above 100 degrees C, because their inorganic network is thermally stable. Acrylic systems are the weakest.

Q: Can the passivation layer protect the coil in a hot environment?
No. Passivation is a short-term anti-white-rust treatment for storage and transport. Continuous high-temperature service requires a different coating, such as aluminised zinc coil.

Q: Why does the film discolour when heated?
Discolouration is oxidation of the film and of the zinc beneath it. Yellow, brown or black appearance indicates that protective function has already been compromised.

Q: Does heat damage affect later painting?
Yes. A cracked, porous film gives poor adhesion and uneven paint appearance, so heat-damaged coil should not be used as a painting substrate without re-treatment.