Does the yield elongation of cold-rolled coil affect stamping?

Mar 16, 2026 Leave a message

1.What is the yield elongation of cold-rolled coils? How does it relate to stamping?

Yield elongation refers to the phenomenon where, during a tensile test, cold-rolled steel sheet continues to undergo plastic deformation after the stress reaches the yield point, without a significant increase in external force. This is represented as a "yield plateau" on the stress-strain curve.

This phenomenon has a direct impact on stamping because:

It is the root cause of uneven deformation: Yield elongation corresponds to uneven plastic deformation within the material. When stamping begins, materials with yield elongation will suddenly deform in localized areas instead of extending uniformly throughout the entire part.

It is a direct cause of surface defects: This sudden uneven deformation forms banded patterns on the surface of the stamped part, i.e., Lüders bands or tensile strain marks, severely damaging the surface quality of the part.

cold-rolled coil

2.How does yield elongation create "stretch marks" on the surface of a stamped part?

Microscopic Mechanism: In cold-rolled coils, interstitial carbon and nitrogen atoms aggregate around dislocations, forming "Coothill clouds" that firmly pin the dislocations. Higher stress is required during stamping to free the dislocations.

Sudden Yielding: Once the stress is sufficiently high, a large number of pinned dislocations break free almost simultaneously, resulting in sudden plastic deformation.

Macroscopic Manifestations: This sudden deformation does not occur uniformly, but rather forms banded slip zones at an angle to the tensile direction on the material surface, known as Lüders bands. These banded regions have different optical properties than the undeformed areas, appearing to the naked eye as patterns or wrinkles.

Results: Stamped parts with this defect, especially outer coverings (such as car doors and hoods), must be scrapped or downgraded because the defect remains visible after painting.

cold-rolled coil

3.Besides causing surface stretch marks, does yield elongation also affect other properties of stamped parts?

Decreased dimensional accuracy: Due to uneven deformation, the springback of stamped parts is difficult to predict and control, resulting in poor dimensional stability and affecting subsequent welding and assembly accuracy.

Local thinning risk: Lüders bands are often areas of concentrated deformation, which may lead to excessive material thinning in these areas, becoming a potential source of stamping cracks.

Uneven mechanical properties: The presence of yield elongation means that the material undergoes uneven deformation in the early stages of stamping, resulting in different degrees of work hardening in different parts of the finished part, ultimately leading to differences in mechanical properties.

Increased die wear: Uneven deformation increases localized stress on the die, accelerating die wear and reducing die life.

cold-rolled coil

4.Why do some cold-rolled coils exhibit yield elongation while others do not? How can this be controlled at the source?

Post-annealing leveling (quenching and tempering): This is the most direct control method. Cold-rolled coils must undergo a leveling process after annealing. By applying a small reduction of 0.8% to 1.5%, dislocations are pre-unpinned, eliminating the yield plateau. If the leveling elongation is insufficient, or if avoiding weld seams results in localized unevenness, these areas will retain yield elongation.

Composition control (source control): Interstitial atoms (C, N) in steel are the root cause of Cotillard atmosphere formation. By adding microalloying elements such as titanium and niobium, which combine with C and N to form stable carbonitrides, the number of solid solution atoms can be reduced, fundamentally lowering the yield elongation tendency. Ultra-low carbon steel (IF steel) achieves its age-free nature through this principle.

Annealing process coordination: Controlling the cooling rate after annealing also affects carbide precipitation behavior, thus affecting yield elongation.

 

5.What should you do if you encounter cold-rolled coils with yield elongation as a stamping user?

Rapid Detection and Confirmation: If in doubt, take samples from both ends of the steel coil for tensile testing and observe the stress-strain curve for a noticeable yield plateau. This is the most direct method of judgment.

Process Adjustment (Temporary Measures):

Pre-deformation Treatment: Before formal stamping, apply a small tensile or bending deformation to the sheet metal (e.g., pass it through a leveling machine) to achieve a similar flattening effect and eliminate the yield plateau.

Adjusting Stamping Speed: In rare cases, changing the stamping speed or blank holder force can reduce the appearance of Lüders bands, but it is usually difficult to completely eliminate them.

Tracing Raw Material Location: Yield elongation defects often concentrate at the head and tail of the steel coil (within approximately 20-50 meters) because the flattening elongation rate may not meet standards during steel mill leveling to avoid weld seams. Try removing more of the head and tail material and using the middle portion to produce critical parts.

Collaborating with Suppliers:

Retain the quality assurance certificates and samples of the problematic batch and raise quality objections with the supplier.

Provide feedback on the specific location of the defect (e.g., which sheet at the beginning of a roll) to help the steel mill trace its leveling process records and find the root cause of the problem.