SGCC, DX51D and Q195 Galvanized Steel Coil for PPGI Sheet Production

Aug 06, 2025 Leave a message

DX51D as a Material Grade

DX51D is a low-carbon, continuously hot-dip zinc-coated steel defined in EN 10346. As a grade it combines moderate tensile strength with very good formability, which is precisely the profile required of a substrate that will be slit, profiled, bent and then painted. In coil form it is supplied with coating masses from about Z100 to Z275, corresponding to roughly 7 to 19 micrometres of zinc per side, and the same product is frequently ordered to the ASTM A653 system as G30 to G90, where the coating designation is expressed in ounces per square foot.

Aluminium-bearing baths are sometimes used instead of pure zinc. A zinc-aluminium coating with about 55 percent aluminium, 43.4 percent zinc and 1.6 percent silicon improves corrosion resistance and surface quality, and the silicon is what keeps the coating ductile enough to survive profiling without flaking.

Coating Mass, Thickness and Corrosion Performance

Coating designation Mass Approximate thickness per side Typical service
Z100 100 g/m2 total about 7 micrometres Interior panels and ducting in mild conditions
Z140 140 g/m2 total about 10 micrometres Sheltered exterior and general indoor use
Z180 180 g/m2 total about 13 micrometres General exterior roofing and cladding
Z275 275 g/m2 total about 19 micrometres Industrial, urban and coastal exposure
G60 / G90 ASTM designation equivalent to about Z180 / Z275 The same products ordered to ASTM A653

Coating mass is the only parameter that can be checked quickly in the warehouse, and it controls service life more than any other single variable. The zinc layer protects the steel both as a barrier and by sacrificial action at scratches and cut edges, so a heavier coating keeps a panel serviceable long after the paint film has lost its gloss.

Formability Grades Above DX51D

DX51D is the entry point of the series. DX53D offers markedly higher formability and is registered under material number 1.0355, with DX54D above it for complex shapes such as automotive exposed panels. Successive editions of EN 10346 have renumbered part of the deep-drawing family, so a purchase specification should quote both the grade and the standard edition instead of relying on an old material number alone. For a coil coating line the choice is simple: DX51D for flat and lightly profiled panels, DX53D and DX54D where the part is deeply drawn or the profile has tight bend radii.

Q195 and Q235B in Structural Applications

Q195 is a Chinese carbon structural steel defined in GB/T 700-2006 with a minimum yield strength of 195 MPa. Its low carbon content gives good ductility, and it has historically been used for light structural sections, purlins and general purpose galvanized framing. Where load-bearing capacity is required, the higher grades of the same standard are preferred, and Q195 has largely given way to Q235B in structural work.

The closest Chinese equivalent to S235JR of EN 10025-2 is Q235B of GB/T 700-2006. The two grades share similar mechanical properties, but subtle differences in chemical composition and in impact testing requirements mean that equivalence must be evaluated case by case before a substitution is accepted for compliance or safety reasons.

How to Specify Galvanized Coil for a PPGI Line

End product Substrate grade Coating Reason
Corrugated roofing and wall cladding DX51D Z180 to Z275 Easy profiling plus long outdoor life
Deeply drawn appliance panels DX53D or DX54D Z100 to Z140 Highest formability before coating
Interior partition and ceiling panels DX51D or SPCC Z100 to Z140 Cost effective indoors
Light galvanized framing Q235B Z120 to Z180 Guaranteed yield strength in the section

Whichever route is taken, the specification should state the grade, the coating mass, the coating type, the surface finish and the standard edition, because two coils that look identical on the bundle can differ in zinc mass and in forming behaviour.

Frequently Asked Questions

Q: What is DX51D material grade?
DX51D is the base commercial quality grade of hot-dip zinc-coated steel in EN 10346, a low-carbon steel with good tensile strength and formability that is widely used as the substrate for prepainted sheets.

Q: What is DX53D steel equivalent to?
DX53D is the next formability class above DX51D and is registered under material number 1.0355; when comparing it with grades from other systems, always quote the standard edition as well as the grade.

Q: What is the difference between DX54D and DX53D?
The letters describe the material: DX denotes the series, the numeral gives the formability grade and D denotes deep-drawing quality, so DX54D forms more demanding shapes than DX53D.

Q: What is the Chinese equivalent of S235JR steel?
The closest equivalent is Q235B of GB/T 700-2006. The mechanical properties are similar, but composition and impact testing differ, so a substitution must be assessed before it is accepted.

Q: What zinc coating thickness is normal for galvanized coil?
Coating is ordered by mass rather than by thickness: Z180 corresponds to about 13 micrometres per side and Z275 to about 19 micrometres, while a measured 20 to 25 micrometres per side indicates a heavy coating reserved for severe environments.

Q: Can DX51D be used outdoors without painting?
Yes, the zinc layer provides sacrificial protection on its own, but a prepainted finish is normally applied because it extends service life and controls appearance.