SPCC, SECC, CRC and HRC Substrates in G350 and G450 Galvanized Coil

Jul 25, 2025 Leave a message

What SPCC, SECC, CRC and HRC Actually Mean

These four abbreviations appear together on galvanized coil offers because they describe the substrate rather than the coating. SPCC is the Japanese designation for cold-reduced carbon steel sheet and strip of commercial quality, defined in JIS G 3141. SECC is the same class of cold-reduced sheet in the electrolytically zinc coated condition, defined in JIS G 3313. CRC and HRC are simply cold-rolled coil and hot-rolled coil: CRC has been rolled at room temperature for a thinner, smoother, more accurate surface, while HRC is rolled at high temperature and is thicker, rougher and usually cheaper per tonne. The metallic coating that makes the product galvanized - zinc from a hot-dip line or from an electrolytic line - is chosen separately from the substrate.

Equivalent Grades and How the Substrate Is Chosen

SPCC is commercially equivalent to Chinese Q195 and Q215A grades and to the older German St12 designation, which has been superseded by DC01 under EN 10130. It is a low-carbon, general-purpose steel intended for bending, profiling and light drawing, not for structural duty. Practical selection follows the forming process and the finished part:

CRC-based SPCC or SECC - thin, smooth panels, appliance housings, ducting and painted components where surface finish matters.

HRC-based coil - thicker sections, tube, purlins and frames where a rougher surface is acceptable and cost is decisive.

SECC - where a thin, uniform, paint-friendly electrolytic zinc coating is preferred over a heavier hot-dip layer.

DX51D hot-dip coil - where a heavier zinc coating and better sacrificial corrosion protection are required.

G350 and G450: Strength Classes for Structural Coil

Where a galvanized coil also carries load, the order switches from a formability grade such as SPCC or DX51D to a strength grade. The letters G followed by a number state the minimum yield strength in megapascals, so G350 guarantees at least 350 MPa and G450 at least 450 MPa. These classes are used for cold-formed purlins, roof decking, wall cladding rails, scaffold planks and racking members, where thin high-strength strip replaces heavier mild steel sections.

Strength class Minimum yield strength Typical galvanized use
G350 350 MPa Purlins, roof and wall cladding, general sections
G450 450 MPa High-strength purlins, decking, racking, long spans

Strength and formability pull in opposite directions: as the guaranteed yield strength rises, elongation and bend performance fall, so corner radii, roll-forming schedules and edge condition must be reviewed whenever a G450 coil replaces a G350 coil on the same profile.

24 Gauge and Metric Thickness Selection

Gauge is a traditional thickness number and its exact value differs between standards, so an order should always state the metric thickness as well. The table below lists the approximate metric equivalents most often quoted for coated steel sheet.

Gauge Approximate thickness Typical galvanized use
26 gauge 0.45 mm Lining panels, trim, light ducting
24 gauge 0.60 mm Roof and wall cladding, ducting, light sections
22 gauge 0.75 mm Cladding, gutter, general fabrication
20 gauge 0.95 mm Purlins, decking, structural panels
18 gauge 1.20 mm Heavy sections, frames, load-bearing members

Quality Control Points for Galvanized Substrate

Confirm the substrate standard and grade, for example SPCC to JIS G 3141 or SECC to JIS G 3313, on the mill certificate.

Verify zinc coating mass and adhesion, and check that the coil surface is free from white rust, uncoated patches and roll marks.

State the required thickness, width and coil weight, and agree dimensional tolerances before rolling.

For strength grades, require tensile and yield test results rather than relying on the nominal class alone.

Match the grade to the forming severity of the line: a softer grade cracks less, a stronger grade carries more load.

Frequently Asked Questions

Q: What is SPCC steel equivalent to?
SPCC is a commercial-quality cold-reduced steel sheet under JIS G 3141, equivalent in practice to Chinese Q195 and Q215A grades and to the former German St12, now covered by DC01 in EN 10130.

Q: Is SPCC stainless steel?
No. SPCC is a plain carbon steel. It has no meaningful chromium content, so it cannot form the passive oxide layer that gives stainless steel its corrosion resistance, which is why it is usually zinc coated or painted.

Q: What is SECC compared with SPCC?
SECC is the electrolytically zinc coated version of the same cold-reduced commercial-quality sheet. The coating is thinner and more uniform than a hot-dip layer, which suits painted appliance and enclosure panels.

Q: What are cold-rolled galvanized coils used for?
Cold-rolled substrates are used for thin, smooth, dimensionally accurate products: appliance housings, office equipment, ducting, containers, ceiling grids and painted building panels.

Q: Is CRC the same as stainless steel?
No. Cold-rolled coil is ordinary carbon steel rolled cold to reduce thickness and improve surface finish. It is cheaper and easier to form than stainless steel but needs a zinc coating or paint for corrosion protection.

Q: What does 24 gauge mean in millimetres?
For coated steel sheet, 24 gauge corresponds to approximately 0.60 mm. Because gauge definitions vary between standards, the metric thickness should always be stated on the order as well.