DX51D Galvanized Coil and DC01 CRC Strip: Grades, Coatings and Formability

Aug 21, 2025 Leave a message

DX51D Galvanized Coil and DC01 Cold-Rolled Strip: Product Definitions

DX51D and DC01 are two of the most widely traded flat steel products, yet they are constantly confused because both are delivered as coil and as cut strip. DX51D is a low-carbon steel for forming that carries a hot-dip zinc or zinc-iron coating, defined in EN 10346. DC01 is an uncoated cold-reduced low-carbon steel defined in EN 10130, previously designated ST12 or material 1.0330 under the withdrawn DIN 1623 specification. Neither grade is stainless steel: both are non-alloy carbon steels with carbon below 0.12%, whereas a genuine stainless coil must contain at least 10.5% chromium. This distinction matters commercially, because DX51D and DC01 are priced on the carbon steel coil market and are protected against corrosion by coating rather than by alloying.

DX51D+Z Coating Designations under EN 10346

EN 10346 completes the DX51D designation with a coating code. DX51D+Z is a pure zinc coating deposited on a continuous hot-dip galvanizing line and is the most common variant. DX51D+ZF carries a zinc-iron alloy layer produced by in-line annealing after coating, which improves welding behaviour and paint adhesion at a small cost in ductility. Aluminium-bearing coatings are chosen where the service life requirement is longer than a pure zinc layer can satisfy. Coating mass is stated per face in g/m² and is the primary variable in corrosion life.

Designation Coating Typical mass per face Typical application
DX51D+Z Pure zinc Z100 to Z275 General forming, panels, ducts
DX51D+ZF Zinc-iron alloy ZF100 to ZF180 Welded and painted components
DX51D+ZA Zinc-aluminium AZ100 to AZ150 Building profiles, long-life outdoors
DX51D+AS Aluminium-silicon AS100 to AS150 Heat-resistant panels, exhaust parts

DC01 Cold-Rolled Strip: Grade Family and Cross-Reference

DC01 is the base grade of the EN 10130 cold-reduced family and is intended for simple forming such as bending, coining, beading and light drawing. Coils are normally skin-passed to suppress the yield-point elongation that would otherwise produce Luders lines on the formed part. The table below gives the usual cross-references requested by buyers who order DC01 CRC strip against more than one standard.

System Designation Note
European EN 10130 DC01 Current specification, material 1.0330
German legacy DIN 1623 ST12 Withdrawn, replaced by EN 10130
Japanese JIS G3141 SPCC Commercial quality cold-reduced
American ASTM A1008 CS Type B Commercial quality, cold-rolled sheet
Chinese GB/T 5213 DC01 Equivalent designation for cold-reduced coil

Mechanical Properties and the Formability Ladder

The DC grade family is ordered by forming severity, not by strength. Moving from DC01 to DC04 widens the yield range downward and raises the minimum elongation, which is what allows progressively deeper draws without tearing. DX51D sits between the two coated and uncoated worlds: it offers a slightly higher yield strength than DC01 because the coating line imposes its own thermal cycle, but it brings sacrificial corrosion protection that an uncoated strip cannot match.

Grade Yield strength Rp0.2 (MPa) Tensile strength Rm (MPa) Elongation A80 min (%)
DX51D+Z 140 to 300 270 to 500 20
DC01 140 to 280 270 to 410 28
DC03 140 to 240 270 to 370 34
DC04 140 to 210 270 to 350 38

Values follow EN 10346 for DX51D+Z and EN 10130 for the DC grades. Thickness is the other decisive variable: DC01 CRC strip is routinely rolled from 0.30 mm to 3.00 mm, and the minimum elongation guarantee applies to the full range only when the strip is ordered with a normal anisotropy coefficient and a strain-hardening exponent declared on the mill certificate.

Surface Finish, Flatness and Fabrication Notes

Surface quality: EN 10130 defines surface types A, B and C by the number of permitted surface defects; DX51D coil is classified as A, B or C in EN 10346 with chromate-free or oiled passivation.

Standard sheet sizes: CRC strip is commonly cut to 1219 mm x 2438 mm and 1219 mm x 3048 mm, the formats referred to as 4x8 and 4x10 in imperial trade.

Flatness: ordered as normal, improved or special flatness, with tighter tolerances available on tension-levelled cut-to-length lines.

Welding: both grades weld with standard low-carbon procedures; zinc-iron alloyed DX51D+ZF is preferred where resistance welding is used, because it avoids the zinc fuming and electrode pickup caused by a pure zinc layer.

Storage: uncoated DC01 must be kept dry and oiled to prevent white rust and edge staining; galvanized DX51D coil tolerates damp transit better but still requires ventilation to avoid wet-storage corrosion.

Selection Guidance and FAQ

The short rule is that DX51D is chosen when the finished part will be exposed to weather without painting, and DC01 is chosen when the part will be painted, plated or welded and the corrosion protection comes from a downstream process. Where both forming severity and outdoor exposure are high, buyers normally move to DC03 or DC04 and apply a coating afterwards rather than forcing DX51D to a draw ratio it cannot hold.

Q: Is DX51D the same as DC01?
No. DX51D is a hot-dip coated forming steel to EN 10346, while DC01 is an uncoated cold-reduced steel to EN 10130. They differ in coating, specification and corrosion behaviour.

Q: Are DX51D and DC01 stainless steel?
No. Both are non-alloy low-carbon steels with carbon under 0.12% and no chromium addition. Stainless coil requires a chromium content above 10.5%.

Q: What does DC01 replace in older drawings?
DC01 replaced the designation ST12 of the withdrawn DIN 1623 and carries material number 1.0330. It is comparable to JIS G3141 SPCC and ASTM A1008 CS Type B.

Q: Which coating mass should be specified for outdoor use?
For unpainted outdoor parts, Z275 on DX51D+Z or an aluminium-bearing coating of AZ150 is typical. Painted parts are usually ordered at Z100 to Z140 because the paint supplies the barrier protection.

Q: Why is cold-rolled strip harder than hot-rolled strip?
Cold reduction plastically deforms the steel below its recrystallisation temperature, so dislocations accumulate and raise yield strength, hardness and resistance to deformation through work hardening.

Q: Can DC01 be deep drawn?
Only for shallow draws. DC01 is rated for simple forming; deep drawing and difficult profiling require DC03 or DC04, which combine a lower yield range with higher elongation.