DX51D+Z is the most widely specified hot-dip galvanized steel in Europe and one of the most commonly imported grades worldwide. The designation comes from EN 10346, the European standard for continuously hot-dip coated steel flat products, and the Z100 coating class refers to the mass of zinc applied to both surfaces. This article explains the designation, the coating, the spangle options, and the relationship between DX51D, DC51D, SGCC, DX52D and DX53D.
What Does the Name DX51D+Z Mean?
In EN 10346 the designation is read in parts. The first letter D identifies a flat product intended for cold forming. The letter X states that the base metal may be produced by either hot rolling or cold rolling - the rolling route is not restricted. The number 51 is the series number of the grade family, and the final D indicates that the product is supplied with a metallic coating applied by continuous hot-dip processing. The suffix +Z specifies a pure zinc coating, while +ZF would indicate a zinc-iron alloy coating. In the European steel numbering system the grade is designated 1.0226.
What Does Z100 Mean?
The coating class is written as Z followed by a number that expresses the total zinc coating mass on both surfaces in grams per square metre, measured by the triple-spot method. Z100 therefore means a minimum of 100 g/m² of zinc across both faces, with a single-spot minimum of 85 g/m² in the same test. Because zinc has a density of about 7.14 g/cm³, Z100 corresponds to roughly 7 µm of zinc on each side. For comparison, Z140 gives about 10 µm per side, Z200 about 14 µm and Z275 about 19 µm.
| Coating class | Total mass (g/m², triple spot) | Approx. thickness per side (µm) | Typical use |
|---|---|---|---|
| Z100 | 100 | 7 | Indoor and light exposure |
| Z140 | 140 | 10 | General building components |
| Z180 | 180 | 12.5 | Roofing and cladding |
| Z200 | 200 | 14 | Roofing, agricultural buildings |
| Z275 | 275 | 19 | Harsh or corrosive environments |
Regular Spangle, Minimized Spangle and Zero Spangle
Spangle is the visible crystalline pattern that forms on the zinc surface as the coating solidifies. Regular spangle shows large, clearly visible crystals and is the traditional finish for roofing and general construction. Minimized spangle is produced by controlling the bath chemistry and cooling so that the crystals are small and barely visible. Zero spangle suppresses crystal growth almost completely, giving a uniform matte surface that is preferred for painting, appliance panels and applications where a smooth appearance matters. The choice of spangle does not change the coating mass, so corrosion resistance is determined by the coating class, not by the spangle appearance.
DX51D+Z, DC51D+Z and SGCC
DC51D+Z is the same grade family with one difference: the base material must be cold rolled, written as the letter C in the designation. DX51D+Z permits either a hot-rolled or cold-rolled base. In practice both are supplied for forming, and the mechanical properties of the base are not guaranteed to fixed minimum values for either designation under EN 10346 - the standard instead verifies formability by bend testing. SGCC is the general galvanized sheet grade of JIS G3302 and is the designation most frequently named as an equivalent to DX51D+Z in Asian trade. It is broadly comparable in use, but the two grades are defined by different standards; buyers should state the governing standard in the order and verify against the mill certificate.
DX51D vs DX52D vs DX53D
The series number rises with forming capability. DX51D is the standard forming grade; DX52D offers higher ductility and better elongation and suits more complex bending and light drawing; DX53D is a deep-drawing grade. For a thickness of 0.5 to 1.0 mm, the guaranteed values per EN 10346 are:
| Grade | Yield strength (MPa) | Tensile strength (MPa) | Elongation A80 min (%) | Typical use |
|---|---|---|---|---|
| DX51D | Not guaranteed | Not guaranteed (typical 270-500) | Bend test | Bending, profiling, general forming |
| DX52D | 140-300 | 270-420 | 24 | More complex bending, light drawing |
| DX53D | 140-260 | 270-420 | 30 | Deep drawing |
Values apply to the 0.5-1.0 mm thickness range and vary with thickness; verify the exact values for the ordered gauge on the mill certificate.
What about DX51D+AZ150?
AZ denotes an aluminium-zinc coating, commonly called aluminium-zinc, containing approximately 55% aluminium, 43.4% zinc and 1.6% silicon. DX51D+AZ150 carries 150 g/m² of this alloy over both surfaces. The aluminium-rich coating gives a longer barrier life and better heat reflectivity than pure zinc in many environments, while the zinc fraction still provides sacrificial protection at cut edges. It is a popular choice for roofing sheets, where the substrate, coating and forming properties of the DX51D family are combined with a longer service life.
FAQ
Is DX51D+Z the same as SGCC?
They are broadly equivalent in use. DX51D+Z per EN 10346 and SGCC per JIS G3302 are both hot-dip galvanized forming grades without guaranteed tensile values. The governing standard, coating class and surface finish should be stated in the order.
What is the difference between +Z and +ZF?
+Z is a pure zinc coating; +ZF is a zinc-iron alloy coating with a matte, spangle-free surface and better weldability, often used in automotive applications where spot welding is heavy.
Which coating class is right for a roof?
For most building roofing, Z200-Z275 per EN 10346, or AZ150 for aluminium-zinc coated sheet, is common. Selection depends on the local climate and building code. The coating mass, not the spangle, governs service life.
Can zero-spangle DX51D be painted?
Yes. Zero spangle is the preferred surface for painting because it is uniform and smooth. The coil still requires proper pretreatment and primer before the final paint film is applied.
Does zero spangle reduce corrosion resistance?
No. Spangle is a cosmetic feature of the zinc surface; corrosion resistance is set by the coating mass and the environment of use.
What thickness and width ranges are typical for DX51D+Z coils?
Common commercial ranges are 0.30-3.00 mm thickness and 600-1500 mm width. Confirm the exact envelope with the producing mill, as capability varies by line.

