What DX52D Galvanized Steel Coil Is
DX52D is a continuously hot-dip coated flat steel grade defined in EN 10346. In the designation, DX marks commercial-quality hot-dip coated steel, 52 is the forming grade, and D indicates that the product ships hot-dip coated. The suffix after the plus sign names the coating: +Z is pure zinc, +ZF is a zinc-iron alloy coating produced by in-line alloying, and +ZM is a zinc-aluminium-magnesium coating. DX52D sits one step above DX51D in drawability and one step below DX53D.
Close equivalents are DC52D+Z in GB/T 2518 and SGCD1 in JIS G3302. ASTM A653/A653M covers comparable zinc-coated drawing-quality sheet through quality classes rather than DX codes, so any conversion should be checked against the current edition of the standard before a coil is released for production.
Manufacturing runs on a continuous line. Cold-rolled substrate is annealed, dipped in a molten zinc bath at roughly 450-460 C, wiped by an air knife to fix the coating mass, cooled, skin-passed and finally surface-treated. Because the strip passes through in one continuous run, coating mass, spangle type and surface finish stay uniform from the head to the tail of the coil, which is what allows successive stamped parts to keep the same appearance and the same corrosion performance.
Recommended Configurations by Application
Configuration means the combination of grade, coating mass, surface finish and temper that a part actually needs. Buying a heavier coating than the service environment requires wastes money and can interfere with forming; buying a lighter one shortens service life. The table below matches the main application families to the configurations that are normally specified for them.
| Application | Typical parts | Coating | Surface finish | Why this configuration |
|---|---|---|---|---|
| Automotive body and closures | Door panels, hoods, reinforcement brackets | Z100-Z140 | Skin-passed, oiled | Supports drawing of curved panels while resisting stone-chip and road-salt attack |
| Automotive interior structure | Seat frames, cross members, brackets | Z100 | Regular spangle, dry | Balances weight, weldability and cost in non-visible parts |
| Home appliances | Refrigerator side panels, washer housings, air-conditioner shells | Z100-Z140 | Zero spangle, passivated | A low-roughness surface takes paint and laminate film and keeps the exterior uniform |
| Building and decoration | Wall panels, roof gussets, ventilation ducts, furniture frames | Z120-Z275 | Regular spangle, passivated | Heavier coating for long outdoor exposure, with good bending behaviour for duct work |
| Hardware and daily goods | Shelving, filing cabinets, drying racks, storage racks | Z60-Z120 | Regular or small spangle | Exploits the strong formability of DX52D at controlled cost |
| Agriculture and livestock | Greenhouse frames, fencing, granary baffles | Z140-Z275 | Passivated, dry | Withstands humid, ammonia-rich air and cuts maintenance at remote sites |
Thickness, Width and Coating Mass
DX52D galvanized coil is normally supplied in thicknesses from about 0.2 mm to 2.0 mm and in widths from 600 mm to 1500 mm, with 1000 mm, 1219 mm, 1250 mm and 1500 mm the most frequently ordered. Coating mass is quoted as the total mass on both surfaces, so a Z100 designation means 100 g/m2 in total, roughly 50 g/m2 per side. As a practical rule, coating mass should follow the corrosivity of the site rather than the thickness of the part: a thin panel inside a coastal plant may need a heavier coating than a thick bracket in a dry inland warehouse.
Z60-Z90: dry indoor environments and short-life consumer goods that will be painted.
Z100-Z140: general industrial and appliance use with occasional condensation.
Z180-Z275: outdoor, humid or mildly aggressive atmospheres such as greenhouses and utility cabinets.
Forming, Joining and Surface Notes
DX52D is specified for its forming behaviour, so how the coil is handled matters as much as which grade is ordered. Deep-drawn or heavily bent parts benefit from an oiled surface, and keeping the coil oiled during storage and forming also limits the risk of white rust appearing before assembly.
Bend radii should be generous relative to sheet thickness when the coating has to remain intact on the outside of the bend.
Welding galvanized sheet needs adequate ventilation and correctly set current, because zinc vapour forms during the process.
Zero spangle finishes hide small paint defects better, while regular spangle is easier to inspect visually for coating discontinuities.
Parts that will be painted should be ordered passivated and oiled according to the recommendation of the paint system supplier.
Quality Checks Before Ordering
A short, fixed checklist removes most disputes. Confirm the grade and the coating designation against the part drawing, read the mill certificate for the mechanical values that the application depends on, and measure coating mass on samples taken from the head and the tail of the coil. Dimensional checks on length, width and thickness, together with a visual inspection for surface defects, are normally enough for a release decision; accelerated corrosion testing is only needed when the finished part will be exposed in a demanding environment.
Frequently Asked Questions
Q: What is the difference between DX52D and DX53D?
Both are hot-dip coated forming grades in EN 10346, but DX53D is the deeper drawing grade with a higher elongation requirement, so it is chosen for more severe stamping than DX52D can carry.
Q: Is DX52D the same as SGCC?
No. SGCC is the commercial-quality grade in JIS G3302 and corresponds more closely to DX51D, while DX52D aligns with SGCD1.
Q: Which coating should be used outdoors?
For continuous outdoor exposure specify at least Z180, and move to Z275, a passivated surface or a zinc-aluminium-magnesium coating where the atmosphere is humid or polluted.
Q: Does mill oil affect paint adhesion?
Mill-applied oil is formulated to be compatible with common paint lines, but the oil type should be confirmed with the coater and excess oil removed before pre-treatment.
Q: Can DX52D be supplied in zero spangle?
Yes. Zero spangle is produced by controlling the zinc bath composition and the cooling rate, and it is usually specified when the part will be painted or laminated and surface appearance matters.
Q: How should the coil be stored?
Keep coils dry, off the floor and under cover; if they must stay outdoors, wrap them and position them so that water cannot collect between the wraps.

