DX51D+Z100 Hot-Dip Galvanized Coil: Grade Meaning and Specifications

Oct 15, 2025 Leave a message

DX51D+Z100 appears on more export quotations than any other galvanized coil specification, yet the designation is often copied incorrectly in listings and enquiries. The name carries three pieces of information: the steel grade DX51D, the coating metal Z (pure zinc) and the coating mass 100 g/m2. This article decodes the full designation under EN 10346:2015, explains the relationship with the Japanese grade SGCC, and summarises the typical thickness and width range supplied on the market.

What Does the DX51D Designation Mean?

In EN 10346, the designation is built from four parts. The first letter D means flat steel for cold forming. The letter X means the rolling state is not restricted, so the substrate may be hot-rolled or cold-rolled. The number 51 is the series number identifying the forming class: 51 is the general bending and forming grade, while 52 and 53 indicate progressively better formability for drawing. The final letter D is the product form symbol for strip and sheet. DX51D is therefore the standard low-carbon bending grade of the continuous hot-dip coated steel family, with a maximum carbon content of 0.18%, a tensile strength range of 270-500 MPa and a minimum elongation of 22%.

Z100 Coating and Its Meaning

The suffix Z100 specifies a pure zinc coating with a nominal total mass of 100 g/m2 measured on both surfaces together, equivalent to a typical zinc layer of about 7 micrometres per side. This coating is the standard choice for indoor and light industrial service, providing sacrificial protection at the cut edges and scratches. Heavier coatings such as Z180 and Z275 are preferred for outdoor and corrosive environments, while lighter coatings down to Z60 are used for simple interior parts.

Coating designation Nominal mass g/m2 (both sides) Typical layer per side Typical service
Z60 60 About 4 micrometres Indoor light parts
Z100 100 About 7 micrometres Indoor and light industrial
Z180 180 About 13 micrometres Semi-outdoor and roofing
Z275 275 About 20 micrometres Outdoor structures, agriculture

DX51D Equivalents and Related Grades

DX51D+Z is commonly accepted as equivalent to SGCC, the Japanese hot-dip zinc-coated steel sheet defined in JIS G3302, and both are routinely used for the same bending, profiling and general fabrication applications. On the Chinese market the same material family is covered by GB/T 2518. For applications requiring deeper drawing, DX52D+Z and DX53D+Z are used; DX53D is an interstitial-free (IF) steel with yield strength of about 130-180 MPa, designed for complex stamping such as automotive and appliance panels. The former designations EN 10142 and EN 10147 have been consolidated into EN 10346, so current certificates should be issued against EN 10346:2015.

Typical Thickness, Width and Delivery Forms

DX51D+Z100 galvanized coil is commonly supplied in thicknesses from 0.45 mm to 3.00 mm and widths up to 1520 mm, with 1000 mm, 1219 mm and 1250 mm being the standard export widths. The product is delivered as coils of 3-8 metric tons, or as sheets cut to length. Surface options include regular spangle, minimised spangle, zero spangle and skin-passed finishes, selected according to the final application: roofing and profiles normally use regular or minimised spangle, while painted and visible panels use zero spangle.

Frequently Asked Questions

What does DX mean in DX51D?

D means flat steel for cold forming and X means the rolling state is not restricted. Together they identify a forming-grade substrate that may be hot-rolled or cold-rolled.

Is DX51D the same as SGCC?

DX51D+Z is widely treated as equivalent to SGCC under JIS G3302 for bending and general fabrication. Both are low-carbon galvanized products with similar formability, although the governing standards differ.

What thickness is available for DX51D?

The common supply range is 0.45-3.00 mm in thickness, with widths up to 1520 mm. Standard export widths are 1000 mm, 1219 mm and 1250 mm.

What does Z100 mean on a galvanized coil?

Z100 means a nominal zinc coating of 100 g/m2 measured as the total mass on both surfaces, equivalent to roughly 7 micrometres per side. It suits indoor and light industrial service.

Which standard governs DX51D+Z coil?

EN 10346:2015, Continuous hot-dip coated steel strip and sheet for cold forming. The older standards EN 10142 and EN 10147 have been consolidated into EN 10346.

When should I use DX53D instead of DX51D?

When the part requires deep drawing or complex stamping. DX53D is an IF steel with yield strength of about 130-180 MPa and significantly better formability than DX51D.