DX51D, DX52D and DX53D: The Ductility Ladder in EN 10346
All three grades are continuously hot-dip coated steels supplied for cold forming with a zinc coating such as Z100, but they sit at different points on the formability scale. DX51D is the bending and profiling grade, DX52D adds elongation for moderate drawing, and DX53D is intended for deep drawn and complex shapes. Selecting one grade higher than the part requires is a common way to pay for ductility that the press line never uses.
| Grade | Yield strength Re (MPa) | Tensile strength Rm (MPa) | Elongation A80 minimum | Typical use |
|---|---|---|---|---|
| DX51D | 140-320 | 270-500 | 22% | Roll-formed cladding, ducting, cable trays |
| DX52D | 140-300 | 270-420 | 26% | Moderate drawing, appliance panels |
| DX53D | 140-260 | 270-380 | 30% | Deep drawn components, switched parts |
The pattern behind the numbers is simple: as the grade number rises, the strength band narrows downwards and the elongation floor rises, which is what makes a deeper draw possible without necking.
DX51D Against DC51D: Two Similar Names, Two Different Jobs
The two designations are confused constantly because the digits look alike. In EN 10346, DX51D is the grade intended for bending and forming, and can be produced from either cold-rolled or hot-rolled pickled substrate depending on the mill route. DC51D is the drawing-quality coated grade of the same standard, normally produced from cold-rolled low-carbon substrate with tighter control of drawing behaviour. Where a mill applies its own enterprise standard, the resulting commercial grades carry shorter designations, but the acceptance pattern stays the same: higher elongation, tighter strength band, better drawability.
Grade Equivalence Table
| EN 10346 grade | Closest JIS G3302 grade | GB/T 2518 designation | ASTM A653 description |
|---|---|---|---|
| DX51D+Z | SGCC | DX51D+Z | Commercial Steel, Type B |
| DX52D+Z | SGCD1, approximate | DX52D+Z | Drawing Steel, Type B |
| DC51D+Z | SGCD, approximate | DC51D+Z | Drawing Steel |
| DX53D+Z | SGCD3, approximate | DX53D+Z | Deep Drawing Steel |
Equivalence is a starting point for enquiry, not a substitute for a specification. The chemical composition, the coating class and the surface treatment still have to be stated on the order, because the same grade name can be delivered in several coating classes.
Z100 Coating on 0.6 mm Coil: Mass, Thickness and Flatness
In the Z series the coating figure is the total zinc mass on both surfaces measured by the triple-spot test of EN 10346, so Z100 equals 50 g/m2 per side. With zinc at 7.14 g/cm3, that is about 7 micrometres of zinc on each face. A 0.6 mm coil carries roughly 212 m2 of surface per tonne, so the Z100 layer represents about 21 kg of zinc per tonne of steel.
| Coating class | Total mass (g/m2) | Per side (g/m2) | Per side thickness | Zinc per tonne of 0.6 mm coil |
|---|---|---|---|---|
| Z100 | 100 | 50 | 7 um | about 21 kg |
| Z140 | 140 | 70 | 10 um | about 30 kg |
| Z180 | 180 | 90 | 13 um | about 38 kg |
| Z275 | 275 | 137.5 | 19 um | about 58 kg |
Flatness is specified separately from coating weight. Skin passing and tension levelling control coil set, crossbow and waviness, and the dimensional tolerances follow EN 10143 in either normal or special grade, the tighter grade being intended for visible panels and for paint lines that cannot tolerate shape defects.
Ordering Data for a 0.6 mm DX51D+Z100 Coil
| Item to state | Typical entry |
|---|---|
| Product standard and grade | EN 10346, DX51D+Z |
| Coating class | Z100, triple-spot average |
| Dimensions | 0.60 mm x 1250 mm, tolerance grade to EN 10143 |
| Surface | Minimized spangle, chromate-free passivated, unoiled or oiled |
| Coil data | Inner diameter 508 mm, weight 3-8 t |
| Documentation | Mill test certificate to EN 10204 3.1 with coating mass report |
Leaving the coating class or the tolerance grade unstated is the usual cause of a coil arriving with the right chemistry and the wrong surface, so both belong on the purchase specification.
Storage, Handling and Forming Practice
Store coils under cover on dunnage clear of the floor, and avoid temperature swings that cause condensation.
Keep the oil film intact during transport and storage to reduce the risk of white rust on the zinc surface.
Do not drag coils or lift them with bare slings; edge damage on a 0.6 mm coil quickly becomes coating damage.
Roll form with adequate lubricant and with rolls that are clean and free of burrs, which protects both the zinc layer and the tooling.
Inspect the coating mass and the surface before the coil enters the paint or profiling line, not afterwards.
White rust appearing in storage is a handling issue rather than a coating defect, and it is prevented by ventilation, prompt use and a protected surface treatment rather than by a heavier coating class.
Frequently Asked Questions
Q: What is the difference between DX51D and DX52D?
DX52D is the more ductile grade: it has a higher minimum elongation and a narrower strength band than DX51D, which makes it suitable for moderate drawing, while DX51D is intended for standard bending and roll forming.
Q: Is DX51D equivalent to SGCC?
SGCC in JIS G3302 is the closest equivalent to DX51D in EN 10346. Their property bands are similar but not identical, so the substitution should be accepted against the delivered certificate values.
Q: What does DX51D Z100 mean exactly?
The DX51D part names the hot-dip coated steel grade for forming, and Z100 names the coating: 100 g/m2 of zinc across both surfaces, which is about 7 micrometres per side.
Q: Which zinc coating class should I choose for roofing?
Z100 suits coated or sheltered panels, while Z275 is the usual choice for exposed roofing and wall cladding in coastal or industrial atmospheres because the extra zinc mass carries the corrosion allowance.
Q: Can DX51D be supplied from hot-rolled substrate?
Yes. The grade can be produced on either cold-rolled or hot-rolled pickled substrate, and the substrate route mainly affects surface quality and thickness range rather than the grade designation.
Q: What thickness and width range is normal for this coil?
Coils in this family are typically rolled from 0.14 mm to 1.5 mm and from 914 mm to 1250 mm wide, with slitting available for narrower strip and a dimensional tolerance grade to EN 10143.

