Galvanized Steel Coil Grades Compared: SGCC, DX51D and ASTM A653

Jun 06, 2025 Leave a message

Three Grade Systems, One Product Family

A galvanized steel coil can be ordered under several national and regional systems, and the same physical product is often described by three different designations. SGCC is the Japanese commercial quality grade under JIS G3302, DX51D is the European bending and forming grade under EN 10346, and ASTM A653M is the US specification for hot-dip zinc-coated steel sheet. Understanding how the systems line up prevents the most common purchasing mistake, which is ordering an equivalent designation and receiving a coil with different formability or coating mass.

SGCC, DX51D and ASTM A653 Compared

Designation System Quality class Main characteristic Coating call-out
SGCC JIS G3302 Commercial quality, low-carbon substrate General purpose, suitable for bending and profiling Zinc mass stated in g/m2
DX51D EN 10346 Bending and forming grade, lowest ductility of the DX series Low yield strength, good profiling behaviour, not structural Z, ZA, AZ or AS coating prefix plus mass, for example Z120
ASTM A653 commercial steel ASTM A653M Commercial steel class for bending duty Widely used in US practice with FS or CS designations Coating class G or AZ plus mass
DC51D+Z EN 10346 Bending and forming on a cold-reduced substrate Cross reference for the SGCC / DX51D family Zinc mass stated in g/m2

The practical equivalence that buyers use most often is DX51D to SGCC. Both describe a low-carbon, cold-reduced substrate that has been hot-dip galvanized and is intended for bending and forming rather than structural duty. The equivalence is a working equivalence, not an identity: the two standards differ in how the base steel composition and mechanical limits are defined, and individual mills apply their own internal ranges inside those limits.

What Equivalence Really Means

Formability is the binding constraint. A grade described as equivalent in one system may be softer or harder in practice, which changes the minimum bend radius and the risk of cracking during profiling.

Coating class is separate from grade. DX51D says nothing about coating mass. The coating must be ordered explicitly, because a coil supplied as Z100 and a coil supplied as Z275 in the same grade will have very different service life.

Substrate condition matters. A hot-rolled galvanized coil and a cold-rolled galvanized coil can share a designation but not the same flatness or surface quality.

Certification is per heat. The mill test certificate states the chemistry and mechanical results for the delivered coil, and that document, not the designation alone, is the acceptance basis.

Coating Designations and the Aluminium-Zinc Family

Coating code Composition Designation example Typical advantage
Z Pure zinc Z100, Z120, Z180, Z275 Reliable sacrificial protection, easy to weld and paint
ZA Zinc with about 5 percent aluminium ZA130 Improved coating adhesion and forming behaviour
AZ About 55 percent aluminium, 43.4 percent zinc, 1.6 percent silicon AZ150 High heat reflectivity and long life in marine and industrial air

AZ150 is the designation most often confused with a zinc coating. It is not 150 grams of zinc: it is 150 grams per square metre of the aluminium-zinc alloy, whose composition is close to 55 percent aluminium, 43.4 percent zinc and 1.6 percent silicon. The alloy coating is specified where heat reflectivity, weight saving and long-term performance under aggressive conditions matter, while pure zinc remains the first choice where sacrificial edge protection and conventional welding practice are more important.

Specifying a Coil Correctly

State the standard and designation together, for example DX51D under EN 10346, not the grade alone.

State the coating code and total coating mass on both surfaces, for example Z120 or AZ150, and say whether the mass is total or per side.

State thickness, width and tolerance, plus the coil inner diameter and the required coil weight range.

State the surface condition, including spangle type, passivation and oiling, because these decide how the coil behaves in painting or profiling.

State the mechanical requirement, especially if the part will be deep drawn or bent to a tight radius, and request the mill test certificate.

State the packing and loading method for the actual transport route, since moisture control during sea freight determines whether the coil arrives free of white rust.

Frequently Asked Questions

Q: Is DX51D the same as SGCC?
They are treated as cross-references for the same application family, a low-carbon galvanized sheet for bending and forming, but they are defined in different standards. DX51D belongs to EN 10346 and SGCC to JIS G3302, and the composition and mechanical limits are not written identically, so the mill certificate should always be checked.

Q: What does DX51D stand for?
The letters indicate a continuously hot-dip coated flat product intended for bending and forming, the number 51 is the grade serial number in the series, and the final letter denotes the coating type plus the coating mass. The steel underneath is a low-carbon cold-reduced substrate.

Q: What is AZ150 material?
AZ150 is a 150 gram per square metre aluminium-zinc alloy coating, with a composition of approximately 55 percent aluminium, 43.4 percent zinc and 1.6 percent silicon. It offers high thermal reflectivity and strong corrosion performance in aggressive environments, and it is frequently ordered on a DX51D substrate.

Q: Can a Z120 coil be substituted by an AZ150 coil?
Not automatically. AZ150 has a higher coating mass and a different alloy, which usually improves atmospheric durability and heat reflection, but the aluminium-zinc coating behaves differently when welded and at cut edges. The substitution should be approved against the actual exposure and fabrication route.

Q: Why do two suppliers quote the same grade at different prices?
Because the grade designation fixes only part of the specification. Substrate route, coating mass, spangle, passivation, thickness tolerance, coil weight and packing all vary and all carry cost. Comparing quotations without matching those parameters usually compares two different products.

Q: Which documents should accompany a galvanized coil order?
The mill test certificate covering chemistry and mechanical properties for the delivered heat, a coating mass record, and packing details including the marking used for traceability. These three documents allow the coating class and grade to be verified on arrival without destructive testing of a full coil.