DC01, SPCC and CRC: What Each Name Covers
DC01 is the base grade of the European cold-reduced drawing steel family defined in EN 10130, and it replaced the older designations St12 and FeP01. It is a low carbon steel intended for simple forming operations such as bending, coining, beading and shallow drawing. SPCC is the JIS G3141 designation for cold reduced carbon steel sheet of commercial quality, and CRC is simply the product form, cold rolled coil. The three terms describe overlapping things: DC01 and SPCC are grades from two standard systems, and CRC is the shape in which either may be supplied.
The grades sit on a formability ladder. DC01 is the entry level, DC03 adds deep drawing capability, DC04 supports high forming requirements, and DC05 and DC06 are ultra low carbon grades for the most demanding draws. JIS G3141 follows the same progression with SPCC for commercial quality, SPCD for drawing quality and SPCE for deep drawing quality, and ISO 3574 covers cold reduced carbon steel sheet of commercial and drawing qualities using the same three tier logic. A buyer who specifies only the letters and not the standard can receive a material that meets one system and misses another.
Mechanical Properties Across the Grade Ladder
| Grade | Yield strength (max) | Tensile strength | A80 elongation (min) |
|---|---|---|---|
| DC01 | 280 MPa | 270-410 MPa | 28% |
| DC03 | 240 MPa | 270-370 MPa | 34% |
| DC04 | 210 MPa | 270-350 MPa | 38% |
| DC05 | 180 MPa | 270-330 MPa | 40% |
| DC06 | 170 MPa | 270-330 MPa | 41% |
The table is read as a trade between strength and ductility. DC01 offers the widest strength band and the lowest elongation, which suits folded covers, panels and simple brackets. Each successive grade lowers the yield ceiling and raises the elongation, buying formability with strength. Choosing DC04 for a simple bend is a cost without benefit, and choosing DC01 for a deep drawn part risks fracture at the punch radius. Under JIS G3141 the chemical requirements tighten in the same order, with the maximum carbon content falling from SPCC to SPCD to SPCE, which is what makes the deeper drawing behaviour possible.
Surface Finish, Flatness and Thickness Tolerance
Cold reduced coil is valued for two things that hot rolled coil cannot match: a smooth surface and a tight thickness tolerance. Surface quality is normally specified as a finish grade, from a fully finished surface suitable for visible painted parts to a surface that may contain minor imperfections where appearance is not critical, and as a surface roughness class expressed as arithmetic mean roughness. Ra values matter directly for painting and for friction behaviour in a press, and a mill that supplies a roughness outside the specified class can cause paint appearance defects even when the mechanical properties are correct.
Flatness is specified as a maximum deviation over a stated length, and it determines whether a laser cutting line or a press feed can run the material at speed. Coil has an additional requirement that sheet does not: residual curvature after uncoiling, which is controlled by the tension levelling or temper rolling step at the end of the line. Thickness tolerance is specified as a plus and minus band and, for narrow strip, may be stated half of the tolerance for the upper half of the width, a rule that matters when the parts are cut close to the strip edge.
Forming, Joining and Finishing
DC01 and its neighbours form readily by bending, roll forming, stamping and shallow drawing, and they weld by resistance spot, seam and arc processes without special preparation. Two effects deserve attention. First, strain ageing: an annealed and skin passed material can develop stretcher strain markings when formed after a period of storage, which is visible as a pattern of lines on a painted surface. Second, springback: the higher the yield strength, the greater the compensation needed in the die, which is one reason the lower yield grades are used for parts with tight dimensional requirements.
Where the part will be painted, the surface must be cleaned and phosphated or otherwise pretreated, and any lubricant residues must be removed, because cold reduced steel has no corrosion protection of its own and will flash rust in a humid workshop within hours of being exposed to condensation. Parts should be stored dry and processed promptly, or protected with a temporary oil film.
Applications and Ordering Points
The main applications are automotive body and structural panels, household appliance enclosures, office furniture panels, electrical enclosures, and the cold reduced substrate that is later galvanized, electrolytically coated or painted. In each case the delivered product should be specified by standard, grade, thickness with tolerance class, width, surface finish class, roughness class and flatness, plus the coil weight range and the edge condition. Two coils with identical grade and thickness can differ in whether they run on a given line purely because of roughness and flatness, so those two parameters should never be left to the mill's discretion.
Frequently Asked Questions
Q: What is DC01 steel?
A: DC01 is the basic grade of the European cold-reduced drawing steel family in EN 10130, formerly designated St12 or FeP01. It is a low carbon steel used for simple forming operations such as bending, coining, beading and shallow drawing.
Q: Is DC01 the same as SPCC?
A: They are similar in application but come from different standards, EN 10130 and JIS G3141. The mechanical property bands and the chemical limits are not identical, so substitution should be checked against the drawing requirement rather than assumed.
Q: What is the difference between DC01 and DC03?
A: DC01 suits simple forming such as bending and beading, while DC03 tolerates deep drawing and difficult profiling. DC03 also has a lower maximum yield strength and a higher minimum elongation than DC01.
Q: Which grade should be chosen for a deep drawn enclosure?
A: DC03 or DC04 is the usual starting point, because the elongation rises to 34% and 38% respectively. The correct grade is finally confirmed by a forming trial, since the tool radius and the lubricant affect the result as much as the material does.
Q: Is CRC supplied with any corrosion protection?
A: Normally only a thin rust preventive oil. Cold reduced coil has no metallic coating, so parts must be processed and protected promptly, or the material must be purchased with a galvanized or painted finish instead.
Q: Why does surface roughness matter for a painted part?
A: Roughness controls how the paint flows and how light reflects from the finished surface, and it also changes friction in the press. A coil outside the specified roughness class can produce paint appearance defects even when the mechanical properties are fully compliant.

