What DX51D Means on a Galvanized Coil Certificate
DX51D is the general-purpose cold-forming grade of the EN 10346 family of continuously hot-dip coated steel sheet and coil. The D stands for flat products for cold forming, the X marks a hot-dip coated product, the figure 51 is the forming series, and the trailing D shows that the steel is intended for drawing and forming rather than for structural duty. Because DX51D is not a structural grade, its certificate gives strength ranges instead of a single minimum value, and the coating is described separately by a Z class. That separation is what allows the same base steel to be delivered as Z275 for an exposed roof sheet or as Z180 for a painted or sheltered part.
Mechanical Properties of the DX Forming Grades
EN 10346 lists a property window for each forming grade, which is why the strength values on a mill certificate vary from coil to coil within the same grade. The following ranges are the values normally quoted for uninterrupted-galvanized material in the relevant forming classes.
| Grade | Yield strength range, MPa | Tensile strength range, MPa | Minimum elongation, percent | Forming capability |
|---|---|---|---|---|
| DX51D+Z | 140 to 300 | 270 to 500 | 22 | Simple bending, roll forming, welding |
| DX52D+Z | 140 to 300 | 270 to 420 | 26 | Stamping and moderate drawing |
| DX53D+Z | 140 to 260 | 270 to 380 | 30 | Deep drawing |
| DX54D+Z | 140 to 220 | 270 to 350 | 34 | Special deep drawing |
Elongation is quoted on an 80 mm gauge length. Where a designer needs a guaranteed minimum strength rather than a forming grade, the specified steel should come from the structural or low-alloy part of the standard instead of the DX series.
Z275 and Z180 Coating Mass Compared
Coating mass is the variable that decides how long a galvanized building sheet survives, and it is also the variable most often misunderstood in quotations. In the EN 10346 convention the figure after the Z is the nominal zinc mass applied to both surfaces combined. Z275 therefore means a nominal 275 g/m² total coating, roughly 137 g/m² on each face, and it is the class used for roofing, cladding and other weather-exposed components. Z180 denotes a nominal 180 g/m² total coating, approximately 90 g/m² per face, and it is chosen where the part is painted, sheltered, or where mass saving matters more than atmospheric life.
| Coating class | Nominal mass, both sides | Approximate mass per side | Typical use |
|---|---|---|---|
| Z180 | 180 g/m² | 90 g/m² | Painted panels, sheltered profiles, interior ducts |
| Z275 | 275 g/m² | 137 g/m² | Exposed roofing and cladding, outdoor structures |
Each class also carries a one-sided minimum for the triple-spot test, and a coating thickness conversion is used during day-to-day inspection: zinc has a density of about 7.14 g/cm³, so 275 g/m² total corresponds to roughly 19 micrometres per face and 180 g/m² total to roughly 12.6 micrometres per face when the coating is equally distributed.
Why the Same Grade Is Bought in Both Coating Classes
DX51D with Z180 and DX51D with Z275 use identical base steel and differ only in the coating applied at the air knife. A manufacturer producing painted wall panels may buy Z180, form and coat it, and rely on the paint system for the outer barrier. The same manufacturer may buy Z275 for an unpainted roofing product where the zinc layer itself must carry the corrosion duty. Keeping the grade constant simplifies forming tools, welding settings and scrap handling, while varying only the coating class adjusts durability and cost per tonne.
Equivalents and Cross-References
SGCC under JIS G3302: the closest Asian equivalent in commercial use, defined by a different standard with its own coating designations.
DC51D+Z under EN 10346: chemically similar, but normally produced from cold-rolled substrate, whereas DX51D can be produced from either cold-rolled or hot-rolled base steel.
Commercial-quality zinc-coated sheet: a generic description used in tender documents where no single standard is named, in which case the coating mass class must always be added.
Ordering and Inspection Points for Building Sheet
For building applications the coating class, the spangle finish, the surface treatment and the dimensional tolerances should all appear on the order. Regular spangle is normal for roofing, small or zero spangle is selected for painted or visible work, and chromium-free passivation or anti-fingerprint treatment is specified when restricted substances or handling marks are an issue. Incoming inspection normally covers coating mass by stripping test, coating thickness by magnetic gauge, reverse-impact or bend adherence, thickness and width measurement, and a salt-spray or humidity check on the finished part rather than on the flat sheet alone.
Frequently Asked Questions
Q: Is DX51D a structural steel grade?
No. DX51D is a cold-forming grade of EN 10346 and is not intended for structural design; where a guaranteed minimum yield strength is required, a structural grade from the same standard should be specified.
Q: What does Z275 mean exactly?
Z275 is a coating class with a nominal 275 g/m² of zinc on both surfaces combined, which is about 137 g/m² per face and around 19 micrometres per face.
Q: Is Z180 a recognized coating class?
Z180 is a nominal 180 g/m² total coating widely traded in the same both-sides convention as Z275; because published class tables differ between standards, the basis of the figure should always be stated on the purchase order.
Q: Can DX51D be supplied in both Z180 and Z275?
Yes. The base steel is the same and only the coating mass applied at the air knife changes, so forming and joining parameters stay constant while corrosion performance and price change.
Q: What is the difference between DX51D and SGCC?
DX51D is defined by EN 10346 and SGCC by JIS G3302; they are used interchangeably in commercial practice but their property tables and coating designations follow different documents.
Q: Which spangle finish is used for building sheet?
Regular spangle dominates unpainted roofing and cladding, while small or zero spangle is preferred for prepainted and visible architectural panels.

