How Carbon Content Affects the Weldability of Q345 Steel

Aug 27, 2025 Leave a message

Why Carbon Is the Element That Governs Q345 Weldability

Carbon is the sensitive element in Q345 steel welding: its content drives crack risk, joint toughness and process complexity more strongly than manganese, phosphorus or sulphur. The relationship is a dose effect, so a small difference in carbon content can decide whether a welded joint passes inspection or fails in service. Understanding where the thresholds lie is what allows a fabricator to set preheat, heat input and post-weld treatment before the first arc is struck.

Carbon Content and the Risk of Cold Cracking

Cold cracking occurs after welding, during cooling, usually in the heat-affected zone or at the weld root, and carbon is the primary cause.

Hardening tendency: higher carbon raises hardenability. The heat-affected zone is austenitised at high temperature and then cools quickly, forming hard martensite that can exceed 350 HV. Toughness drops sharply, and residual welding stress can then crack the joint with no external load.

Reported trend: raising carbon in Q345 from 0.16% to 0.20% is associated with more than 30% additional martensite in the heat-affected zone and a two to three fold increase in cold cracking risk.

Hydrogen interaction: carbon traps diffusible hydrogen, which accumulates at the boundary between weld metal and heat-affected zone. Above a critical level, commonly taken as 5 mL per 100 g of deposited metal, hydrogen together with residual stress initiates cracking. GB/T 1591 caps carbon at 0.20% for thicknesses up to 60 mm, and the same ceiling applies to the Q355 series that replaced the Q345 designation in the 2018 edition. Above that ceiling, preheating in the range 150–250 °C and post-heating at about 250 °C for two hours do not guarantee freedom from cracking.

Joint Toughness: Weld Metal and Heat-Affected Zone

Matching joint properties to the base metal is the core requirement for Q345 welding, and carbon disturbs this balance in both zones of the joint.

Weld metal: carbon transferred from the base metal into the molten pool raises the carbon equivalent of the deposit, promotes network carbides and lowers absorbed impact energy. Reported data shows that raising base metal carbon from 0.14% to 0.20% can drop weld metal Charpy energy at −20 °C from about 50 J to below 30 J, which is under the 34 J required for D-grade material.

Heat-affected zone: carbon promotes austenite grain growth at high temperature and increases the proportion of martensite and bainite, so toughness in that zone can fall 30% to 50% below the base metal. Welding Q345 at 0.20% carbon may leave heat-affected zone Charpy energy at −40 °C below 20 J, which will not satisfy E-grade requirements.

Carbon equivalent: GB/T 1591 sets a maximum carbon equivalent for each grade, calculated with the IIW relationship CEV = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15. When carbon is deliberately kept low, manganese and micro-alloying elements still have to be balanced so that the carbon equivalent stays inside the limit, which is why carbon content should always be read together with the full ladle analysis.

Carbon Content and Welding Process Control

The higher the carbon content, the tighter the process window, and the more the operation costs in time and consumables.

Base metal carbon Preheat requirement Heat input window Post-weld treatment
0.14%–0.16%, plate up to 16 mm Room temperature welding is normally acceptable 10–40 kJ/cm Usually omitted on thin plate
0.18%–0.20%, plate from 12 mm 80–120 °C, and above 150 °C in a cold workshop 15–30 kJ/cm Stress relief holding at 600–650 °C
Above 0.20% Outside the grade ceiling; cracking cannot be excluded Narrow window only Mandatory, yet reliability is still not guaranteed

Two practical points follow from the table. First, heat input must be held inside a window: too high and the heat-affected zone grains coarsen, too low and the cooling rate is fast enough to form martensite. Second, hydrogen control, including dry electrodes and clean joint faces, matters most precisely where carbon content is near the upper limit.

Safe, Risk and Danger Ranges for Carbon Content

Range Weldability Reported outcome
Carbon at or below 0.16% Excellent, conventional procedures apply Low cold cracking risk, no strict preheating, joint toughness acceptance above 90%
Above 0.16% up to 0.20% Moderate, demanding control Preheat, heat input and hydrogen must all be controlled; joint toughness acceptance falls to about 70–80%
Above 0.20% Poor, outside the standard ceiling Significant cold cracking and toughness shortfall; the joint no longer satisfies the grade requirement

In practice, the lower end of the permissible carbon range is the safer choice. Where the structure is thick, for example above 20 mm, or the service temperature is below −20 °C, a difference of 0.02% carbon can be the deciding factor between a sound joint and a rejected one.

FAQ

Q: How much does carbon content affect Q345 weldability?
It is the dominant factor. Carbon controls hardenability, so it sets cold cracking risk, heat-affected zone toughness and how much preheat, heat input control and post-weld treatment a joint needs.

Q: What is the maximum carbon content allowed in Q345 or Q355 steel?
GB/T 1591 caps carbon at 0.20% for thicknesses up to 60 mm. The Q355 designation in the 2018 edition applies the same ceiling that previously applied to Q345.

Q: At what carbon content is preheating required?
Below about 0.16% carbon, thin plate can normally be welded at room temperature. From 0.18% upward, even 12 mm plate is generally preheated to 80–120 °C, and higher in cold conditions.

Q: Why does higher carbon reduce joint toughness?
Carbon coarsens austenite grains in the heat-affected zone and increases martensite and bainite, while raising the carbon equivalent of the weld metal. Both effects lower Charpy impact energy.

Q: Does post-weld heat treatment fix a high carbon joint?
Stress relief holding at 600–650 °C reduces residual stress and softens hardened structures, but it cannot restore toughness that was already lost or remove the risk taken by exceeding the carbon ceiling.

Q: Which carbon level should be specified for low temperature service?
For structures below −20 °C or thicker than 20 mm, specify the lower end of the grade range, in the region of 0.14% to 0.16% carbon, and verify the carbon equivalent of the ladle analysis rather than the nominal grade alone.