1.How to control substrate quality from the source?
Substrate Surface Cleanliness: Upon arrival, substrates are rigorously inspected to ensure they are free of oil (such as rolling oil residue), rust (including minor rust), scratches, indentations, pitting, and other defects. Oily substrates are difficult to completely remove during pre-galvanizing degreasing, which can lead to localized missed plating. Rust may leave corrosion pits after pickling, resulting in uneven zinc coating adhesion.
Substrate Chemical Stability: The silicon (Si ≤ 0.03%) and phosphorus (P ≤ 0.025%) content in the substrate is carefully controlled to avoid excessive silicon content, which can lead to "silicon reaction" (the formation of an insoluble oxide film on the surface during galvanizing, hindering the zinc coating's adhesion, resulting in "blackening" or missed plating). Excessive phosphorus content can increase substrate brittleness and easily crack the zinc coating during subsequent processing.
Substrate Shape Accuracy: Ensure substrates are free of wavy or warped shapes. Poor shape can easily cause scratches from friction with guide rollers in the galvanizing line, or uneven stress can lead to uneven zinc coating thickness (locally too thin or too thick).

2.How to remove impurities from the substrate surface?
Degreasing: Thoroughly remove oil contamination to prevent plating skips.
Process parameter optimization: Use an alkaline degreasing agent (such as sodium hydroxide + surfactant), control the temperature to 50-80°C, and degreasing for 3-5 minutes (adjusted according to the amount of oil contamination). A combination of spraying and immersion can enhance degreasing effectiveness. If the oil contamination is heavy, pre-treat it with physical wiping.
Post-degreasing cleaning: After degreasing, rinse with warm water (40-50°C) 2-3 times to ensure that no degreasing agent residue is present (residue can cause uneven reaction during subsequent pickling). After rinsing, check the pH value of the substrate surface (6-7, neutral). Pickling: Precisely removes scale and prevents over-/under-pickling.
Acid control: Use a 15-20% hydrochloric acid solution at a temperature between 20-40°C (high temperatures can lead to over-pickling of the substrate, while low temperatures can result in incomplete scale removal). Add 0.1-0.3% corrosion inhibitor (such as hexamine) to reduce acid corrosion on the substrate (avoiding "pitting").
Pickling endpoint determination: Visual inspection (substrate surface uniform silver-gray, with no residual dark-brown scale) or time control (usually 2-4 minutes, adjusted depending on scale thickness) to prevent "under-pickling" (residual scale prevents zinc from adhering, resulting in missed plating) and "over-pickling" (micro-pitting on the substrate surface, resulting in a rough zinc layer after galvanizing).

3.How to prevent zinc layer from being rough and zinc particles?
Zinc liquid purity: Control impurities in the zinc liquid (iron ≤ 0.03%, lead ≤ 0.02%, cadmium ≤ 0.01%). Excessive iron content will form Fe-Zn alloy slag (floating or deposited), which adheres to the strip surface and forms "zinc scars." Regularly remove slag from the zinc liquid surface with a slag remover (once every two hours), or add a zinc liquid purifier (such as aluminum wire) to absorb impurities.
Temperature Control: The zinc liquid temperature should be maintained at a constant 440-460°C (±5°C). Excessively high temperatures will result in coarse zinc layer grains (rough surface) and increased zinc consumption. Excessively low temperatures will result in poor zinc liquid fluidity and uneven zinc layer thickness (thick at the edges and thin in the middle). Real-time temperature control is required using a heating device (such as induction heating).

4.How to ensure uniform zinc layer and strong bonding?
Matching zinc immersion time and speed: Adjust the speed according to the strip thickness (usually 10-30 m/min). For thin gauges (≤1 mm), the speed can be slightly faster to prevent the zinc coating from becoming too thick, while for thick gauges (>1 mm), the speed can be slightly slower to ensure adequate zinc adhesion. Keep the zinc immersion time within 3-5 seconds. A longer time can result in a thick and rough zinc coating, while a shorter time can lead to insufficient adhesion.
The angle of the strip entering the zinc bath: Maintain a 15-30° angle between the strip and the zinc bath surface. Avoid vertical entry (which can easily entrap air bubbles and cause bulging in the zinc layer) or a shallow angle (which can cause scratches due to friction with the zinc bath surface).
5.How to prevent scratches and uneven zinc layer?
Sinking Roller/Stabilizer Roller Maintenance: Regularly inspect the surfaces of the sinking and stabilizing rollers in the galvanizing tank (once a week) to ensure they are free of zinc sticking and wear (zinc sticking can cause indentations on the strip surface, while worn roller surfaces can easily scratch the strip). If zinc sticking is present, clean it promptly with specialized tools to avoid damaging the chrome plating on the rollers.
Air Knife Parameter Optimization: After galvanizing, an air knife (high-pressure air) is used to blow away excess zinc liquid. Control the air knife pressure (0.2-0.4 MPa) and distance (10-20 mm from the strip). Excessive pressure can lead to locally thinner zinc coatings or "air knife marks" (striped color variations), while insufficient pressure can result in excessively thick zinc coatings. The air knife nozzle must be kept clear (cleared once a week) to prevent clogging and uneven zinc coating thickness.

