Define the Application Requirements First
Cold-rolled galvanized sheet is sold by grade and coating designation, and the designation only makes sense once the job is described. Three questions resolve most specifications:
Environment: will the part see moisture, acid, alkali, high temperature or chloride-laden coastal air? This sets the required coating mass and coating type.
Processing route: shearing, bending, deep drawing, welding and painting each demand a different balance of ductility, surface quality and coating adhesion.
Function: load bearing, impact resistance or visible appearance, including the freedom from spangle and the smoothness required for painting.
Select by Corrosion Resistance: Coating Mass and Coating Type
Corrosion performance is governed first by coating mass, expressed in grams per square metre over both faces unless stated otherwise, and second by the coating family.
| Service condition | Typical coating | Example designations | Notes |
|---|---|---|---|
| Dry indoor, for example appliance back panels and filing cabinets | Standard zinc, Z80 | DC01+Z80, DX51D+Z80 | Lowest cost that still protects cut edges indoors |
| Wet or industrial indoor, for example kitchen equipment and ventilation ducts | Medium zinc, Z120 to Z180 | DC01+Z120, SGCC with Z60 per side, equal to Z120 both faces | Good balance of cost and durability |
| High salt spray or coastal outdoor, for example guardrails and marine fittings | Heavy zinc Z275 and above, or zinc-aluminium-magnesium alloy coating | DC01+Z275 | Zinc-aluminium-magnesium coatings typically deliver several times the corrosion life of pure zinc at similar mass |
| Parts to be welded or painted | Zinc-iron alloy coating, ZF | DC01+ZF | Uniform, low weld spatter, excellent paint adhesion |
Select by Forming Severity: Ductility and Grade
The more severe the forming operation, the higher the elongation and the deeper the drawing grade required. Use the three-step rule below.
Simple work such as shearing, straight bending and shallow drawing: commercial grades are sufficient, for example EN DC01, GB DX51D or ASTM CS Type B, typically with elongation of 28% or more.
Medium forming such as curved bending and washer housings: deep drawing grades are appropriate, for example EN DC03, GB DX52D or JIS SGCD1, typically with elongation of 34% or more and improved resistance to wrinkling.
Severe forming such as multi-pass stamping of fuel tanks or precision parts: extra deep drawing grades are required, for example EN DC04, GB DX53D or JIS SGCD2, typically with elongation of 38% or more, so the steel survives heavy deformation without cracking.
Balance Strength Against Ductility
| Priority | Grade family | Yield strength level | Comment |
|---|---|---|---|
| Strength for structural parts and brackets | ASTM HSLAS, high strength grades such as EN DC05 high strength | About 300 to 500 MPa | Choose the lower end when some forming is still needed |
| Ductility for complex formed parts | Deep drawing grades DC03, DX52D | Low strength, high elongation | Best formability where load is not critical |
| Balanced strength and formability | High strength deep drawing grades such as EN DC06 and GB DX54D | About 200 to 300 MPa | Elongation of 36% or more, well suited to automotive structural parts |
Match the Regional Standard
Projects often name the standard system of the region or the client, so confirm the relevant specification before quoting a grade.
European projects: EN 10346 and the DC01 to DC06 series.
Domestic projects: GB/T 2518 for hot-dip zinc coated sheet, with grades such as DX51D, DX52D and DX53D.
North American projects: ASTM A653/A653M with commercial steel, CS Type B, and drawing steel designations.
Japanese and Korean supply chains: JIS G3302, with grades such as SGCC, SGCD1 and SGCD2.
The same physical sheet is frequently available under more than one designation, but the customer's quality department will inspect against the standard named in the order, so any substitution must be agreed in writing before production.
Avoid Over-Specification and Cover Special Needs
Ultra deep drawing grades combined with the heaviest coatings are expensive, and paying for capacity the part never uses is the most common source of avoidable cost.
Ventilation ducts: DC01+Z80 covers the duty; DC03+Z120 is usually unnecessary.
Indoor racking in a low-corrosion room: pure zinc coating is enough, and a zinc-iron alloy coating adds cost without benefit.
Appliance panels with high appearance requirements: specify a spangle-free surface, for example DC01+Z with spangle-free treatment, which gives a smoother face and a better painted finish.
Food contact parts such as refrigerator linings: choose a coating that satisfies food-contact requirements and avoids harmful elements such as lead.
High temperature parts such as oven components: choose a heat-resistant coating, such as an aluminium-zinc alloy coating that withstands temperatures above 300 degrees Celsius.
Frequently Asked Questions
Q: What is the difference between DX51D+Z80 and SGCC with Z60 per side?
Both describe the same order of coating mass, about 80 g/m2 both faces, but they come from different standard systems. Keep the designation used by the project standard to avoid inspection disputes.
Q: When should I choose a zinc-iron alloy coating instead of pure zinc?
Choose it when the part will be welded or painted. The alloyed layer gives consistent welding and excellent paint adhesion, but it offers less sacrificial protection at cut edges than pure zinc.
Q: Can I use DC01 for a deep drawn part to save cost?
Only within the drawing limit of the grade. If the forming operation exceeds what the 28% elongation grade tolerates, cracking losses will cost more than the higher grade.
Q: How much coating mass is needed near the coast?
Specify Z275 or a zinc-aluminium-magnesium alloy coating. The heavier coating or alloy layer extends the interval before red rust appears at edges and scratches.
Q: Is a thicker sheet always stronger?
No. Strength comes from the grade and yield strength, not gauge alone. Selecting a high strength grade at a lighter gauge often reduces weight and cost at the same performance.
Q: How do I verify the coating mass after delivery?
Use a coating mass test on samples taken from several coil positions, either by the gravimetric strip method or by an X-ray fluorescence gauge, and compare the result with the designation on the order.

