What Surface Gloss Tells You About a Galvanized Coil
Gloss on a galvanized coil is not a decorative extra; it is a fast indicator of how the zinc surface will behave downstream. A bright, evenly reflecting surface usually means the zinc layer is smooth, continuous and well formed, while a dull or patchy surface points to a coarse spangle, an incomplete skin-pass or uneven solidification. Because galvanized strip is often used unpainted for appliance panels, cable trays, ducting and pre-coated substrates, gloss is frequently written into the delivery specification alongside coating mass.
Measuring it correctly requires one extra step compared with a painted surface: the metallic zinc coating scatters light according to its crystalline texture, so the reading depends on the measurement angle and on how the sample is oriented relative to that texture.
How a Gloss Meter Reads a Metallic Coating
A gloss meter projects a collimated beam onto the surface at a defined angle and measures the light reflected at the mirror angle with a receiver. The instrument compares that reflected intensity with the intensity reflected by a certified standard plate and reports the result in gloss units, GU. The method itself is standardised in ISO 2813 and ASTM D523, and the same physical principle applies whether the surface is a cured paint film or a bare zinc coating.
The difference is what the beam sees. A paint film reflects from a smooth organic layer, whereas a galvanized surface reflects from metal crystals separated by grain boundaries, so part of the incident light is scattered instead of being returned specularly. The result is a generally lower and more orientation-sensitive reading, which is why texture direction must be recorded and kept constant across a measurement series.
Choosing the Measurement Angle for Galvanized Surfaces
| Geometry | Reading range | When to use it on galvanized coil |
|---|---|---|
| 60° | 10-70 GU | Default geometry for most galvanized coil products |
| 20° | Above 70 GU | Very bright, mirror-like surfaces such as polished or anti-fingerprint finishes |
| 85° | Below 10 GU | Coarse, matte surfaces such as unpolished strip with a large spangle |
The 60° angle covers the bulk of galvanized production. The practical rule is to start at 60°: if the reading comes out above 70 GU the surface is outside the sensitive part of that geometry and the sample should be re-measured at 20°, and if it falls below 10 GU it should be re-measured at 85°. The 20° beam resolves small differences between bright surfaces, while the 85° beam gathers enough light from a dull surface to produce a stable number rather than one pinned near zero.
How Spangle Size Changes Gloss
Spangle is the visible zinc crystal pattern formed as the coating solidifies. Its size and regularity drive the gloss level far more than most operators expect.
Regular spangle: distinct, shiny snowflake or star shaped crystals that are relatively large. Because each crystal face is smooth and reflects light well, the surface appears bright, but the grain boundaries scatter light locally, so readings can vary from point to point.
Small spangle: produced by suppressing crystal growth with controlled cooling such as a water mist or steam spray. The pattern becomes fine and almost invisible, giving a uniform surface with a more even reflection.
Unpolished small spangle: typically off-white with low gloss, sitting in the matte range and reading below 10 GU at 60°.
Skin-passed small spangle: the standard finish for demanding applications. The surface becomes smooth and flat, gloss rises markedly and the coating takes on a uniform mirror-like appearance.
Skin-Pass Finishing and the Move to a Mirror Finish
Skin-pass rolling is the process that turns a dull galvanized surface into the bright finish used for appliance panels and painted substrates. A light reduction pass through a temper mill flattens the microscopic relief left by solidification, which raises specular reflection and therefore gloss. The same pass removes yield point elongation, the effect that otherwise produces stretcher strain marks when the strip is formed, so the sheet stretches smoothly in the press.
The practical consequences for gloss control are twofold. First, gloss is measured after skin-passing, because the temper mill changes the surface more than any other step in the line. Second, roll condition matters: a worn or dirty temper roll prints its own dull pattern onto the strip, and the resulting variation appears as streaks in a gloss map long before it is visible to the eye.
Reporting and Interpreting Gloss Results
A gloss figure on its own is not a specification. A useful report states the measurement angle, the instrument, the number of readings and their average, the sampling positions across the coil width, and the surface finish of the material, for example regular spangle or skin-passed. Because the zinc texture is directional, the orientation of the instrument relative to the rolling direction should also be recorded and repeated on every sample from the same order.
When readings drift, the sequence to investigate is: confirm calibration against a certified plate, check that the sample is flat and clean, verify that the measurement orientation has not changed, then look at the line. A single low reading usually means a contaminated window or a scratched sample, while a systematic shift across a coil normally points to a change in skin-pass condition or in cooling practice at the galvanizing pot.
Frequently Asked Questions
Q: Which angle is used for gloss measurement on galvanized coil?
Start with 60°, the general purpose geometry. Move to 20° when the reading exceeds 70 GU and to 85° when it falls below 10 GU.
Q: Why is galvanized strip usually less glossy than painted strip?
The zinc crystals and their grain boundaries scatter part of the incident light, so less light returns at the specular angle and the gloss value is lower.
Q: Does spangle affect the gloss reading?
Yes. Large regular spangle reflects brightly but unevenly between crystals, while a fine small spangle gives a lower and more consistent reading.
Q: What does skin-passing do to gloss?
It flattens the surface relief created during solidification and removes yield point elongation, which raises gloss and improves formability at the same time.
Q: Should the measurement orientation be recorded?
Yes. Zinc texture is directional, so the instrument orientation relative to the rolling direction must be kept constant and noted on the report.
Q: Why does the same coil give different readings at different points?
Local crystal size, minor surface scratches and uneven skin-pass contact create genuine point-to-point variation, which is why several readings are averaged.

