What Counts as Light-Duty Steel Grating
Light-duty steel metal grating is engineered for pedestrian walkways, maintenance platforms, machinery floors and light rolling traffic such as carts and hand trucks. The panels are fabricated from carbon steel as bar grating, using swaging, riveting, dovetailing or welding to lock load-bearing bars together with perpendicular cross bars into a stiff open grid. The open pattern is the whole point: it drains water and process spillage, ventilates the space beneath, and gives a slip-resistant walking surface without the weight and ponding problems of a solid plate.
Because the panels are economical, durable and need very little maintenance, they are widely used for industrial safety barriers, catwalks and highway drainage covers, indoors and outdoors alike. Light-duty sections are also chosen where a structure has to satisfy OSHA walking-working surface requirements without adding unnecessary dead load to the frame.
How a Bar Grating Panel Is Assembled
Bearing bars - the deep, load-carrying members that span between supports and set the panel's strength.
Cross bars - perpendicular twisted or plain bars that hold the pitch, brace the assembly and provide the walking surface.
Joining method - swaged, riveted, dovetail-pressed or welded, each giving a different balance of cost, stiffness and finish quality.
Finish - carbon steel panels are supplied bare for dry indoor service or hot-dip galvanized for exterior and wet duty; where galvanizing to EN ISO 1461 is specified, bars 3 mm and heavier normally carry a coating averaging at least 55 µm with a 45 µm local minimum.
Bearing Bar Sizes Used in Light-Duty Panels
The light-duty range is built around 3 mm and 5 mm bearing bar thicknesses, with depth rising as the span increases:
| Bearing bar size (depth × thickness) | Panel series | Typical duty |
|---|---|---|
| 20 × 3 mm | G203 | Short-span covers, screens |
| 25 × 3 mm | G253 | Pedestrian walkways, light platforms |
| 32 × 3 mm | G323 | Walkways with light rolling loads |
| 40 × 3 mm | G403 | Longer spans in the light-duty range |
| 20 × 5 mm | G205 | Stiffer short-span panels |
| 25 × 5 mm | G255 | General walkway and platform work |
| 32 × 5 mm | G325 | Upper end of light duty |
| 40 × 5 mm | G405 | Transition to medium duty |
| 45–60 × 5 mm | G455 / G505 / G555 / G605 | Medium and heavier duty spans |
Reading the G-Series Panel Designation
Each code packs three facts into one string. In G325/30/100, the letter G identifies the product as steel grating, the digits 32 and 5 give the bearing bar depth and thickness in millimetres, the next number is the bearing bar pitch and the last is the cross bar pitch. So G325/30/100 is a panel with 32 × 5 mm bearing bars at 30 mm spacing and cross bars at 100 mm spacing. Writing a specification this way removes ambiguity for both the fabricator and the installer.
Pitches and What They Change
Bearing bar pitch - standard options are 30 mm, 40 mm and 60 mm. A tighter pitch raises stiffness and load capacity per panel, and also reduces the chance of a heel or trolley wheel dropping through.
Cross bar pitch - normally 50 mm or 100 mm. The 50 mm pitch gives a denser walking surface and better grip; 100 mm saves weight and cost where traffic is light.
Bar depth - the single most effective lever on span. Increasing depth from 20 mm to 40 mm lifts stiffness far more than adding the same amount of bar thickness.
Applications and Selection Notes
Typical installations are fixed walkways in plants, access platforms around machinery, mezzanine flooring, trench and drainage covers, and stair treads. Selection starts from the clear span and the actual load case - a footfall and a hand truck are very different inputs - then picks the lightest panel that carries that load within the permitted deflection. Edge banding, cut-outs and fixing clips are normally detailed at the same time, because how a panel is anchored to the frame usually governs whether it stays flat under traffic.
FAQ
Q: What span can light-duty steel grating cover?
It depends on bar size and pitch rather than on a single figure: a 3 mm bar at a tight pitch suits short spans and light foot traffic, while 32 × 5 mm or 40 × 5 mm panels extend the same family to longer walkway bays. The load case, not the product name, sets the limit.
Q: How do I read a designation such as G325/30/50?
G for grating, 32 × 5 mm bearing bar, 30 mm bearing bar pitch and 50 mm cross bar pitch. The format is fixed, so any supplier reading the code sees the same panel.
Q: What is the difference between 50 mm and 100 mm cross bar pitch?
The 50 mm pitch gives a denser surface, better grip and more cross bracing; 100 mm pitch is lighter and cheaper and is normally adequate where traffic is pedestrian only.
Q: Should light-duty grating be galvanized?
For outdoor, coastal or wash-down service, hot-dip galvanizing is the usual choice because the coating protects cut edges and the open grid cannot be painted reliably. Dry indoor installations can use bare carbon steel.
Q: Does open-grid grating meet safety requirements for walkways?
The open pattern drains and ventilates and resists slipping, and light-duty panels are commonly specified to satisfy OSHA walking-working surface rules where the surface, openings and edge protection are detailed correctly.
Q: How is the grating fixed down?
Panels are typically seated on the supporting frame and locked with saddle clips, welded studs or bolted brackets. Positive fixing matters, because an unsecured panel can lift or shift under rolling loads.

