CGCC Zero Spangle Galvanized Steel Coil and GI Sheet Explained

Oct 29, 2025 Leave a message

Coated coil is ordered by a short code that mixes the base metal, the coating type and the surface appearance, and CGCC is one of the common commercial designations used in Asian and Middle East trade. This guide explains what the code means, how zero spangle differs from regular spangle, and which specification values change when the coil is ordered for a specific application.

What CGCC and Zero Spangle Mean

CGCC is the trade description of continuously galvanized cold reduced commercial coil. It corresponds in practice to SGCC of JIS G 3302, DX51D+Z of EN 10346 and commercial steel of ASTM A653, which are the designations used when the same material is ordered against an international standard. The base metal is cold rolled low carbon steel that has been annealed, skin passed and then passed through a molten zinc bath on a continuous line.

Spangle is the visible crystalline pattern formed as the zinc coating solidifies. Zero spangle is produced by suppressing normal crystal growth during cooling, so the surface is smooth and uniform with no visible splatter. Regular spangle, minimum spangle and big spangle are also available, and the choice is mainly a matter of appearance and of how the surface will be painted or printed later.

Base Metal and Coating Designations

Because the coating is applied to a cold reduced substrate, the mechanical properties come from the annealed base metal rather than from the zinc layer. The zinc layer provides the corrosion barrier and, for a zero spangle product, is applied with stricter control of bath chemistry and coating weight uniformity than a commercial regular spangle line.

System Commercial grade Structural or high strength Coating designation
Trade / mill code CGCC G350, G450, G550 Z40 to Z275
JIS G 3302 SGCC SGCH, SGC400, SGC440 Z18, Z27, Z35
EN 10346 DX51D+Z DX52D+Z, DX53D+Z, S250GD+Z Z100 to Z600
ASTM A653 CS Type B Grade 50, Grade 80 G40 to G185

The G350, G450 and G550 codes denote minimum yield strength in MPa for high strength galvanized grades, so they should not be read as coating weights. Coating mass, by contrast, is always given as a zinc figure such as Z275, which equals 275 g/m2 total on both faces.

Specification Range

Parameter Range
Material SGCC, SGCH, G350, G450, G550, DX51D, DX52D, DX53D
Thickness 0.12 mm to 4.0 mm
Width 20 mm to 1250 mm
Zinc coating Z40 to Z275 g/m2, with heavier coatings available on request
Hardness Soft, about HRB 60; medium hard, HRB 60 to 85; full hard, HRB 85 to 95
Surface structure Regular spangle, minimum spangle, zero spangle, big spangle
Surface treatment Chromated or non chromated, oiled or non oiled, skin passed
Coil form Inner diameter 508 mm or 610 mm, slit strip from 20 mm

Thickness, width and coating mass are quoted at a defined measuring point, and buyers should expect the coating figure to be stated as a minimum average over the sheet rather than as a single local reading. A skin passed surface is usually specified when the coil will be painted, because it flattens the surface profile and improves paint adhesion.

Spangle and Surface Treatment Options

Zero spangle gives a smooth, uniform appearance and is preferred for visible panels, painted products and printed parts.

Regular spangle shows the familiar crystalline pattern and is the standard finish for general building and industrial use.

Minimum spangle sits between the two and is chosen when a small pattern is acceptable but a fully smooth surface is not required.

Chromate passivation reduces the risk of white rust during transport and storage, and non chromated alternatives are available where chromate free material is required.

Oiling protects the surface during handling and forming, while dry, non oiled coils are supplied for immediate painting lines.

Where the coil will be roll formed into decking, purlins or profile sheet, the coating must be able to follow tight bends without cracking, so coating adhesion and bend performance are tested on the finished product rather than judged from the coil surface alone.

Typical Applications

Building and structure: purlins, wall beams, roof and wall panels, support components for factories, warehouses and terminals.

Building enclosure: substrate for colour coated steel tiles and facade panels that need a long decorative life.

Infrastructure: bridge auxiliary parts, noise barriers, cable trays, light poles and transmission tower accessories.

Automotive and transport: internal body structure, chassis parts, heat shields, container boards and van bodies.

Industrial equipment: agricultural machinery housings, construction machinery covers and tool boxes, ventilation ducts and fan housings.

Electrical enclosures: distribution cabinets, control cabinets and equipment housings.

Frequently Asked Questions

Q: Is CGCC the same as SGCC?
In commercial practice they describe the same continuously galvanized commercial quality cold reduced coil. SGCC is the JIS G 3302 designation, while CGCC is the trade code used on many mill certificates and order sheets.

Q: Why choose zero spangle instead of regular spangle?
A zero spangle surface is smoother and more uniform, which gives better appearance and more consistent paint and print results. Regular spangle is generally cheaper and is adequate where appearance is not critical.

Q: What does a Z275 coating deliver?
Z275 means 275 g/m2 of zinc in total across both faces, roughly 137 g/m2 per face, which is about 19 micrometres of zinc per side and matches the G90 designation of ASTM A653.

Q: How is hardness classified on galvanized coil?
Soft material is around HRB 60 and bends and forms easily, medium hard covers HRB 60 to 85 for structural profiles, and full hard runs HRB 85 to 95 for decking and sections that need stiffness rather than formability.

Q: What is the minimum thickness available?
Galvanized coil is commonly produced from 0.12 mm to 4.0 mm, with the thinnest gauges used for packaging and light profile work and heavier gauges for structural sections.

Q: Does the zinc coating change the mechanical properties?
The properties are set by the cold reduced, annealed base metal. Galvanizing adds a thin coating that protects the surface, so a Z275 coil and a Z180 coil of the same base grade have the same strength and elongation.