Cold Rolled Coils in 0.35 mm and 0.5 mm Thickness
Thin cold-rolled coil from 0.35 mm to 0.5 mm is ordered where weight saving, tight thickness control and a paint-quality surface are the priorities. Because 0.35 mm is the lower limit of the EN 10130 thickness range for cold-rolled low-carbon flat products, coils at this gauge are produced with careful rolling and annealing control, and the surface must be free from scale, roll marks and edge damage that would show through a finished coating.
Typical applications for this range include steel drums and pails, lighting housings, cable trays, cable-armouring tape, packaging closures, appliance panels and automotive inner parts. In each case the buyer normally fixes three things at order stage: the forming grade, the thickness and width tolerance, and the surface quality class.
DC01 and DC04: Grade Comparison
DC01 is the basic cold-rolled grade of EN 10130 (material number 1.0330) and replaces the former St12 and FeP01 designations. DC04 is the deep-drawing grade that replaced St14. The chemical limits in the standard tighten as the forming class rises, which is what allows the deeper drawing behaviour.
| Element (% by mass) | DC01 | DC03 | DC04 |
|---|---|---|---|
| Carbon C max | 0.12 | 0.10 | 0.08 |
| Manganese Mn max | 0.60 | 0.45 | 0.40 |
| Phosphorus P max | 0.045 | 0.035 | 0.030 |
| Sulphur S max | 0.045 | 0.035 | 0.030 |
| Aluminium Al min | 0.020 | 0.020 | 0.020 |
| Grade | Yield strength Re (MPa) | Tensile strength Rm (MPa) | Elongation A80 min (%) |
|---|---|---|---|
| DC01 | 140-280 | 270-410 | 28 |
| DC03 | up to 240 | 270-370 | 34 |
| DC04 | up to 210 | 270-350 | 38 |
In thin gauges the difference between the grades shows up quickly. A 0.35 mm component that must be drawn into a drum lid or a deep housing needs the elongation and low yield strength of DC04, whereas a simple bent bracket at 0.5 mm is usually economic in DC01.
What the JSC270D Designation Means
JSC270D belongs to the Asian cold-rolled grade system, where the code combines a steel type, a tensile-strength class of about 270 MPa and a drawing-quality suffix. In practice it is used for stamping stock with a moderate strength level and good formability, mainly for automotive and industrial press parts.
Because the letter codes differ between the European, Japanese and American systems, a JSC270D requirement cannot be converted by name alone. The correct method is to compare the certified yield strength, tensile strength, elongation and surface quality with the EN 10130 grade that comes closest, and then agree the substitution in writing. This avoids a situation where a grade is accepted as "equivalent" but fails the forming trial.
Thickness, Width and Shape Tolerance
Metric orders: dimensions and tolerances per EN 10131, with thickness tolerance classes agreed for critical forming.
Japanese system orders: dimensions and tolerances per JIS G3141, which also defines the commercial, drawing and deep-drawing quality classes.
Inch-pound orders: tolerances per ASTM A568/A568M, with the corresponding commercial steel grade to ASTM A1008/A1008M.
For thin material below 0.5 mm, crown, centre buckle, edge wave and camber are the shape features that most often cause problems in automatic feeding and in printing or coating lines. It is normal practice to agree the shape limits together with the thickness tolerance rather than accepting a general tolerance alone, because a coil can be perfectly on thickness and still fail at the press.
Coil Supply and Processing Notes
Cold-rolled coils in this thickness range are typically supplied with an inside diameter of 508 mm or 610 mm, a mill edge or trimmed edge, and either dry or lightly oiled. Coils are wrapped, strapped and marked so the heat number and inspection certificate stay traceable to the coil.
When processing thin cold-rolled coil, three practical points protect the finished part:
Keep the material dry and handle coils by crane with a proper C-hook or coil grab to avoid edge damage.
Level or tension-level before blanking so coil set does not translate into an out-of-flat panel.
Set press tool clearance against the actual certified thickness, since the relative effect of a small thickness deviation is much larger at 0.35 mm than at 2 mm.
DC01 and DC04 both weld readily by spot and seam processes and accept paint, powder and zinc-rich primers after degreasing. Where the finished part is exposed to moisture, an electrolytically zinc coated product to EN 10152 keeps the smooth painted appearance while adding sacrificial protection at the cut edge.
FAQ
Q: Is 0.35 mm the thinnest cold-rolled coil available?
It is the lower limit of the EN 10130 range for cold-rolled low-carbon flat products, which makes it a practical minimum for coil ordered to that standard.
Q: Which grade should be used for a 0.5 mm press part?
Simple bends can use DC01. If the part involves deep drawing or difficult profiling, DC03 or DC04 is the safer choice because of the higher elongation.
Q: Is JSC270D the same as DC01?
No. It comes from a different designation system with a 270 MPa tensile-strength class, so equivalence must be confirmed by comparing certified mechanical properties, not by the code.
Q: Are the chemical limits the only difference between DC01 and DC04?
No. Both the chemical limits and the mechanical requirements differ, and the higher forming class is what makes deep drawing possible.
Q: How should thin coil be stored before pressing?
Keep it dry, off the floor and clear of condensation, and let cold coils reach workshop temperature before uncoiling to avoid surface moisture marks.
Q: Can thin cold-rolled coil be supplied slit to width?
Yes. Slit strip is cut from the master coil to the ordered width and is used for roll forming, tube welding and continuous press lines.

