Q275

Aug 22, 2025 Leave a message

Q275 is a carbon structural steel grade specified in the Chinese national standard (GB/T 700). It is a high-strength carbon structural steel with clear specifications for its performance and applications. The following is a detailed introduction to Q275:
1. Grade Meaning
"Q": stands for the pinyin abbreviation for "yield strength," and the following digits represent the steel's yield strength.
"275": indicates the steel's yield strength is no less than 275 MPa (megapascals), a core mechanical property indicator. (Note: When the grade number is missing a letter (e.g., Q275), it defaults to hot-rolled or normalized steel, with no special impact toughness requirements. If it contains a letter (e.g., Q275A, Q275B), it indicates different impact toughness grades: Grade A does not require an impact test, while Grade B requires a room temperature (20°C) impact test.)
II. Key Performance Indicators
According to GB/T 700, the key properties of Q275 are as follows:
Mechanical Properties:
Yield Strength (σs): ≥275 MPa (thickness ≤16 mm); decreases slightly with increasing thickness (e.g., ≥265 MPa for thicknesses 16-40 mm, ≥255 MPa for thicknesses 40-60 mm).
Tensile Strength (σb): 490-630 MPa.
Elongation (δ5): ≥17% (thickness ≤40 mm). Impact Toughness: For Q275B grade, the impact energy absorbed at room temperature (20°C) is ≥ 27J (V-notch).
Chemical Composition (mass fraction, %):
Carbon (C): ≤ 0.29% (The higher carbon content is the primary reason for its higher strength than Q235).
Manganese (Mn): ≤ 1.50%.
Silicon (Si): ≤ 0.35%.
Phosphorus (P) and Sulfur (S): ≤ 0.045% (As harmful elements, their contents must be strictly controlled to ensure the steel's toughness).
III. Processing and Heat Treatment Characteristics
Weldability: Due to its higher carbon content (compared to Q235), its weldability is moderate. Preheating is required to avoid cracking during welding, making it suitable for methods such as arc welding.
Cold Workability: It has some cold deformation capability, but its cold bending and stamping performance is slightly inferior to that of Q235. It is suitable for medium-deformation cold working (such as cold rolling and bending). Heat Treatment: Normalizing can refine the grain size and improve mechanical properties. If higher hardness is required, quenching and tempering can be used (however, carbon steel has poor hardenability and is primarily used for simple load-bearing parts).
IV. Hardness Reference
Hot-rolled: Brinell hardness (HB) approximately 130-170 (varies slightly due to rolling process and cooling rate).
Cold-rolled: After cold working, hardening increases the hardness, potentially reaching 180-220 HB (depending on the amount of deformation).
V. Application Scenarios
Q275 has higher strength than Q235 and is suitable for structural parts or components that bear medium loads, such as:
Gears, shafts, and connectors (such as bolts and nuts, which must meet certain strength requirements) in machinery manufacturing.
Brackets and load-bearing components in construction and engineering (but attention should be paid to welding procedures).
Load-bearing components in agricultural machinery and vehicles. VI. Main Differences from Q235
Specifications: Q235, Q275
Yield Strength: ≥235MPa, ≥275MPa
Tensile Strength: 375-500MPa, 490-630MPa
Carbon Content: Low (≤0.22%), High (≤0.29%)
Strength: Medium, High
Weldability: Good, Medium (requires process control)
Applications: Low-load structural parts, Medium-load structural parts
In summary, Q275 is a medium-strength carbon steel with a good cost-effectiveness. It is widely used in applications where strength is required but alloy steel is not required. When purchasing, please confirm the specific mechanical properties based on the thickness, and specify the delivery condition (hot rolled/cold rolled) and impact grade (A/B).