Seven Grade Codes, Two Steel Systems
Cold rolled steel coil is ordered by grade code rather than by a general description, because the code fixes the steelmaking route, the guaranteed mechanical level and the surface quality the mill must deliver. Q235 and Q275 come from the Chinese carbon structural steel family defined by GB/T 700, while SPCC, SPCD, SPCE, SPCF and SPCG come from the cold-reduced carbon steel sheet and strip family defined by JIS G3141. The two families are traded side by side but they answer different questions: the Q grades guarantee strength, while the SP grades guarantee formability.
| Grade | Standard | Guaranteed level | Typical use |
|---|---|---|---|
| Q235 | GB/T 700 | Minimum yield strength 235 MPa up to 16 mm, tensile 370-500 MPa | General structures, brackets, ducts, drums, panels |
| Q275 | GB/T 700 | Minimum yield strength 275 MPa up to 16 mm, tensile 410-540 MPa | Higher-load structures, machinery parts, sections |
| SPCC | JIS G3141 | Commercial quality, no yield strength guarantee | Bending and light presswork, appliance shells, containers |
| SPCD | JIS G3141 | Drawing quality | Moderate draws, housings, furniture parts |
| SPCE | JIS G3141 | Deep drawing quality | Deep drawn panels, automotive inner parts |
| SPCF | JIS G3141 | Deep drawing quality for severe forming | Complex drawn parts with tight radii |
| SPCG | JIS G3141 | Deep drawing quality for the most severe forming | Very severe draws where ageing resistance also matters |
Q235 and Q275 are structural grades. Their yield strength is a design value and the chemistry is controlled so that strength, elongation and weldability stay predictable. SPCC through SPCG are forming grades: they are specified mainly by tensile range, elongation, plastic strain ratio and resistance to stretcher strains after ageing, and they carry no minimum yield strength. That difference is why an order that says only cold rolled 1.0 mm is incomplete for anything beyond simple bending.
How Cold Rolling Changes the Coil
Cold rolled coil starts life as hot rolled coil. The hot band is pickled to remove mill scale, then cold reduced in a tandem mill, usually by 60 to 80 percent of its thickness. Cold reduction work hardens the steel: strength and hardness rise, and internal stress rises with them. Because a heavily work hardened coil cannot be formed, it is annealed afterwards, either in a batch furnace or on a continuous annealing line, to restore ductility. A final temper rolling pass of roughly 0.5 to 1.5 percent elongation sets flatness, suppresses stretcher strains and gives the surface a controlled roughness so that paint or lubricant takes evenly. The coil is oiled before packing to slow surface rusting.
The practical results are consistent. The cold rolled product is stronger, harder and flatter than the hot rolled coil it came from, the thickness tolerance is much tighter, and the surface is smooth and uniform. The trade-off is residual stress, which shows up as springback and coil set. Press tools, levellers and roll forming lines have to be set for it, and parts that must stay flat after slitting benefit from a tension levelling pass.
Dimensions, Tolerances and Coil Parameters
| Parameter | Typical range | Note |
|---|---|---|
| Thickness | 0.20-3.0 mm | 0.5, 0.8, 1.0, 1.2, 1.5 and 2.0 mm are the most common sizes |
| Width | 600-1500 mm full coil | From about 100 mm after slitting; exact range is mill dependent |
| Inner diameter | 508 mm or 610 mm | Matched to the customer uncoiler |
| Coil weight | 3-20 t | Heavier coils reduce handling cost per ton |
| Edge | Mill edge or slit edge | Slit edge gives a cleaner, more accurate width |
| Surface | Matte, dull, bright or specified roughness | Chosen for forming, painting or appearance |
Dimensional tolerances for cold rolled sheet and strip follow GB/T 708, which sets permissible thickness and width deviation, flatness and camber. JIS G3141 fixes the same family of limits for SP grades, so a buyer comparing offers from different mills should compare the tolerance class and not only the nominal thickness.
What Drives the Price per Ton
Hot rolled substrate: the largest element in the cost. A rolling margin is added on top of the hot band price.
Thickness: 0.3 mm requires more rolling passes and more annealing capacity than 2.0 mm, so the price per ton rises as the gauge falls.
Width and coil weight: narrow slit coil carries more trimming loss and more handling per ton than full width coil.
Annealing route: continuous annealing gives more uniform properties and costs more than batch annealing.
Temper grade and surface: extra flatness or a controlled roughness adds processing steps.
Quantity and delivery: small lots, non-standard widths and short lead times cost more per ton than a full coil order.
Market cycle: coil offers follow the hot rolled index, so a quotation is normally valid for a limited period only.
Checks Before the Coil Ships
Mill test certificate matched to the ordered heat number, with yield, tensile and elongation for the Q grades.
Thickness profile across the width and along the length, compared with the ordered tolerance class.
Surface inspection for scale, scratches, roll marks and edge cracks.
Coil identity: weight, inner and outer diameter, and eye to sky or eye to wall packing orientation.
Hardness or plastic strain ratio for forming grades where the drawing operation is severe.
Choosing Between a Q Grade and an SP Grade
If the part is a structure, a bracket or anything whose design depends on yield strength, order a Q grade and state the quality grade and impact requirement when the part works at low temperature. If the part is formed in a press and strength is not the design driver, order an SP grade and state the drawing severity. Where both are needed, for example a load-bearing panel drawn from thin coil, the specification has to name a strength floor and a forming class at the same time, which is normally settled with the mill before the order is placed.
Frequently Asked Questions
Q: Is cold rolled steel stronger than hot rolled steel?
Yes. Cold reduction work hardens the steel, so yield strength and hardness are higher than in the hot rolled coil the material came from. The same work hardening raises internal stress, so springback is larger and the material is less tolerant of severe forming before it is annealed.
Q: Which European grade is closest to SPCC?
EN 10130 DC01 is the usual commercial-quality counterpart, but the two are not interchangeable. DC01 is specified through its own mechanical and surface requirements, and the closest match for a drawing application is normally DC03 or DC04 rather than DC01.
Q: What thickness and width are normally available?
Thickness runs from about 0.20 mm to 3.0 mm and full coil width from about 600 mm to 1500 mm. Slit coil can be supplied down to roughly 100 mm wide. Availability at the extremes depends on the mill and on the order quantity.
Q: Does cold rolled steel rust?
Yes, if it is bare. Cold rolled coil has no corrosion protection of its own, so it is oiled for short-term storage and either painted, coated or galvanized for long-term service. Uncoated coil left outdoors will rust.
Q: Is Q235 the same as SPCC?
No. Q235 is a structural grade with a guaranteed minimum yield strength. SPCC is a forming-quality designation with no yield guarantee. They also differ in chemistry control and in how they behave in a press.
Q: Can a Q grade be supplied with the surface of an SP grade?
A mill can deliver Q235 or Q275 cold rolled coil with a specified flatness, surface finish and tolerance class, and the appearance can match commercial quality sheet. What it will not do is guarantee deep drawing behaviour, so severe formed parts should still be specified to SPCD, SPCE or higher.
Q: How is the price per ton quoted?
Offers are usually given per metric ton on an ex-works or delivered basis, with the thickness, width, temper grade and coating state of the surface all fixed in the offer. Extras for thin gauge, narrow width or tight tolerance are added to the base tonnage price.

