Matching the Grade to the Job
A galvanized coil is defined by two things: the base steel grade and the coating. The grade determines strength and formability; the coating determines corrosion life. Specifying a coil by a list of grade names without understanding which applies to your part leads to overpaying or under-specifying. The practical families are: forming grades such as DX51D+Z and DX52D+Z from EN 10346 for stamping and profiling, structural grades S250GD to S550GD from EN 10346 with guaranteed yield strength for load-bearing sections, and general carbon grades such as Q235 from GB/T 700 for economical structures and general fabrication.
Forming Grades: DX51D and DX52D
DX51D+Z is the most common hot-dip coated forming grade in Europe and Asia. Its yield strength of 140 to 300 MPa and tensile strength of 270 to 500 MPa suit bending, roll forming and light stamping, and it accepts coating classes from Z100 to Z450. DX52D+Z offers a tighter tensile range of 270 to 420 MPa with higher minimum elongation, giving better formability for more demanding parts. Neither is intended for severe deep drawing; for that, use DX53D or DX54D.
Structural Grades: S250GD to S550GD
The S-series grades in EN 10346 guarantee a minimum yield strength: S250GD for 250 MPa, S280GD for 280 MPa, S350GD for 350 MPa, S550GD for 550 MPa, with proportional tensile ranges. They are used for profiled sections, purlins, cladding rails, decking, racks and load-bearing frames where the strength of the formed section is part of the structural calculation. S550GD is a high-strength grade for demanding sections where weight matters. Note that higher strength generally reduces bendability, so tight-radius bending should be verified against the grade.
| Grade | Min yield (MPa) | Typical use |
|---|---|---|
| DX51D+Z | 140-300 | General forming, profiling, light stamping |
| DX52D+Z | 140-300 | More demanding forming |
| S250GD+Z | 250 | Light structural sections |
| S280GD+Z | 280 | Profiles and cladding rails |
| S350GD+Z | 350 | Purlins, structural sections |
| S550GD+Z | 550 | High-strength load-bearing profiles |
| Q235+Z | 235 | Economical general structures |
Coating Systems: GI vs GL
GI (hot-dip zinc) coatings protect by barrier plus sacrificial action: the zinc corrodes preferentially at scratches and cut edges, which makes GI the right choice for cut parts and outdoor structures. GL (aluminium-zinc, about 55% aluminium, 43.5% zinc, small silicon addition) gives better heat reflection, higher temperature resistance and longer surface life in moderate exposure, but it provides little sacrificial protection at cut edges. Choose GI for structural parts, cut edges and aggressive environments; choose GL for roofing, cladding and heat-reflecting panels where edge protection is less critical.
Coating Mass Designations
Coating mass is expressed differently by standard. In EN 10346, classes such as Z100, Z140, Z200, Z275 and Z350 state the total zinc mass on both sides in g/m2. In ASTM A653, designations such as G60 and G90 state the coating in ounces per square foot total both sides, where G90 equals about 275 g/m2. Trade terms such as G350 usually mean 350 g/m2 total coating mass. The table below gives approximate equivalents.
| EN class | Approx. ASTM | Total coating mass (g/m2) |
|---|---|---|
| Z100 | G30 | 100 |
| Z180 | G60 | 180 |
| Z275 | G90 | 275 |
| Z350 | - | 350 |
| Z450 | - | 450 |
Common Coil Problems and Solutions
Bending cracks in coated coil usually come from excessive inclusions such as manganese sulphide, uneven microstructure, edge burrs or micro-cracks from slitting, or an improper cold-bending process such as too small a mandrel and too fast a speed. The response is to verify the steel grade and certificate, improve the edge quality, and increase the bend radius. For checking coil quality on receipt, review the certificate for composition, mechanical properties, dimensions and surface grade, inspect the appearance for excessive defects, and carry out random mechanical and dimensional checks. Edge defects such as cracks, burrs and tapered edges are controlled by billet quality, finishing-mill side guides, coiling tension and edge trimming. Thick iron oxide scale on hot-rolled coil is reduced by controlling furnace temperature and time, keeping descaling water pressure adequate, typically at least 18 MPa, using secondary high-pressure descaling, and cooling and packing the coil promptly.
FAQ
What is the difference between DX51D and S350GD?
DX51D is a forming grade with yield 140-300 MPa and no minimum strength guarantee for structural design, while S350GD guarantees a minimum yield of 350 MPa and is used for load-bearing profiled sections.
What does Z275 mean on a galvanized coil?
Z275 means a total zinc coating mass of 275 g/m2 on both sides, per EN 10346. It is roughly equivalent to ASTM A653 G90 and suits outdoor structures.
What causes bending cracks in Q235 coil?
Common causes are excessive inclusions such as manganese sulphide, uneven microstructure, edge burrs or micro-cracks, and improper cold-bending parameters such as too small a mandrel or too fast a bending speed.
How do I check the quality of a received coil?
Verify the certificate for composition, mechanical properties, dimensions and surface grade; inspect the appearance; and carry out random checks of mechanical properties and dimensional tolerances per the applicable standard.
What is the difference between GI and GL coated coil?
GI is a zinc coating with sacrificial edge protection; GL is an aluminium-zinc coating with better heat reflection and surface life in moderate exposure but little cut-edge protection.
How is oxide scale on hot-rolled coil controlled?
By controlling furnace temperature and time, maintaining descaling water pressure, typically at least 18 MPa, using secondary descaling, and cooling and packing the coil promptly after rolling.

