Why Steel Grade Equivalence Needs Careful Checking
Steel grades from different national standards are often compared to find an equivalent material for a project. Because each standard defines its own chemical composition limits, mechanical properties, testing methods and delivery conditions, an equivalent designation means similar behaviour for a defined purpose, not identity. The tables below summarize the most frequently compared grades for cold-rolled and structural steel products.
Grade Equivalence Overview
| Designation | Standard | Product form | Minimum yield strength (MPa) |
|---|---|---|---|
| Q195 | GB/T 700 | Structural steel, wire, sheet | 195 |
| Q235 | GB/T 700 | Structural steel, pipe, plate | 235 |
| Q345 (replaced by Q355) | GB/T 1591 | High-strength structural plate | 345 |
| SS400 | JIS G3101 | Rolled steel for general structure | 245 (up to 16 mm) |
| S235JR | EN 10025-2 | Structural steel | 235 |
| SPCC | JIS G3141 | Cold-rolled sheet | reported; tensile min 270 |
| DC01 | EN 10130 | Cold-rolled sheet for forming | 130-260 (range) |
| A1008 CS/DS | ASTM A1008 | Cold-rolled carbon steel sheet | 170-310 (typical range) |
| G550 | AS/NZS 1397 / GB/T 2518 | High-strength galvanized steel | 550 |
Grouping by Intended Use
For structural purposes the direct comparisons are Q235, SS400 and S235JR (all around 235 MPa yield), and Q345-Q355, S355JR and A572 Grade 50 for high-strength applications. For cold-rolled sheet for forming, the comparisons are DC01 (EN 10130), SPCC (JIS G3141) and A1008 CS Type B (ASTM A1008), with deep drawing versions DC04, SPCD/SPCEN and A1008 DS/DDS. G550 is a separate family: high-strength galvanized sheet with a guaranteed minimum yield strength of 550 MPa, used for cold-formed sections such as purlins and roof sheeting, and covered in AS/NZS 1397 or GB/T 2518.
Quality Carbon Steels 10# and 45#
10# and 45# are Chinese quality carbon structural steels defined in GB/T 699. 10# is a very low-carbon steel (about 0.07 to 0.13% carbon) used for parts requiring high ductility and good weldability, such as tubes, chains and lightly loaded machine parts. 45# contains about 0.42 to 0.50% carbon and is a medium-carbon steel used for shafts, gears and machine parts that are hardened and tempered. Neither belongs to the structural sheet family: 45# in particular is heat-treated rather than cold formed.
Practical Guidance for Substitution
Before substituting one grade for another, compare the guaranteed minimum yield strength, tensile range, elongation, impact requirements, chemical limits (especially carbon equivalent for welding) and the delivery condition in the relevant standard edition. For certified projects, the applicable design code determines which standards are accepted, and the mill certificate must show the actual test values.
Frequently Asked Questions
Is Q235 the same as SS400?
Both are general structural steels with similar strength (minimum yield 235 MPa for Q235, 245 MPa for SS400 up to 16 mm thickness). They are commonly treated as equivalents in practice, but GB/T 700 and JIS G3101 define different composition limits and testing rules.
What is the difference between SPCC and DC01?
SPCC is the general cold-rolled grade in JIS G3141 and DC01 the basic cold-forming grade in EN 10130. Both are low-carbon cold-rolled sheets with comparable strength; DC01 specifies a yield range of 130-260 MPa and a tensile range of 270-410 MPa, while SPCC guarantees a minimum tensile strength of 270 MPa.
What does G550 mean in galvanized steel?
G550 designates high-strength galvanized sheet with a guaranteed minimum yield strength of 550 MPa, commonly specified in AS/NZS 1397 and GB/T 2518 for cold-formed structural sections.
What is A1008 steel?
A1008 is ASTM A1008, the standard for cold-rolled carbon steel sheet, which includes commercial steel (CS), drawing steel (DS), deep drawing steel (DDS) and extra deep drawing steel (EDDS) types, plus structural grades.
Is 45# steel equivalent to any European grade?
45# (GB/T 699, about 0.45% carbon) is comparable to C45 in EN 10083-2, a medium-carbon steel for quenching and tempering. It is not a cold-forming sheet grade and should not be compared with DC or SPCC designations.
What is the closest European grade to Q345?
The closest grade in current European practice is S355 (for example S355JR in EN 10025-2); within GB/T 1591-2018, Q345 has itself been replaced by Q355.

