St37, St52, Q195, Q215 and Q235 are mild and low-alloy structural steel designations that still appear side by side in export enquiries, even though they come from different standards and different eras. Understanding the designation logic prevents specification errors: St37 and St52 are legacy German designations, while the Q-series follows the Chinese GB system with explicit yield values.
What the Designations Mean
In the old German standard DIN 17100, St37 indicated structural steel with a minimum yield strength of 235 MPa (the name came from a tensile strength of 370 MPa) and St52 indicated a higher-strength grade with a minimum yield of 355 MPa. The Q-series in the Chinese GB system is self-explanatory: Q235 means a minimum yield strength of 235 MPa, and the number after Q is the guaranteed yield in MPa for the base thickness range.
Mechanical Property Comparison
| Grade | Standard | Yield strength | Tensile strength |
|---|---|---|---|
| St37 (S235) | DIN 17100 / EN 10025 | >= 235 MPa (<=16 mm) | 360-510 MPa |
| St52 (S355) | DIN 17100 / EN 10025 | >= 355 MPa (<=16 mm) | 490-630 MPa |
| Q195 | GB/T 700 | >= 195 MPa | 315-430 MPa |
| Q215 | GB/T 700 | >= 215 MPa | 335-450 MPa |
| Q235 | GB/T 700 | >= 235 MPa (<=16 mm) | 370-500 MPa |
St37 is the direct historical equivalent of S235 in EN 10025, and St52 of S355. The values above reflect the guaranteed properties in the governing standards for plate up to 16 mm.
Delivery Documents and Re-Inspection
Structural steel orders should ship with a mill test certificate stating the grade, standard, heat number, chemical composition and mechanical test results. In the Chinese inspection practice, re-inspection of a batch is conducted per lot, with the batch size defined by the standard; for example, Q235 plate is commonly re-inspected in batches not exceeding 60 tonnes, with samples taken from the batch for chemical and mechanical testing. Confirm the sampling clause with your quality team so the receiving inspection matches the standard's rules.
Surface Inspection of Mild Steel Plate
Check delivered plate for laminations, cracks, scratches and scale pits. Minor surface defects are often acceptable if they can be removed by grinding without reducing the thickness below the minimum; deep defects that violate the tolerance should be rejected. Rust and mill scale on the surface are normal for as-rolled plate unless pickled, but heavy pitting from wet storage indicates a storage problem and should be reported immediately.
Q235 vs Q345: Which One to Choose
Q235 is the workhorse for general structures, fences, supports and non-critical welded frames. Q345 or its successor Q355 adds about 50% more guaranteed yield, allowing lighter sections and lower total steel tonnage, at a higher unit price. For trusses, crane supports and structures where dead weight matters, run the design in both grades and compare the delivered cost of the optimized sections before deciding.
FAQ
Is Q235 suitable for scaffolding?
Yes, Q235 is widely used for scaffolding tubes and couplers, and the welded frames are checked against the applicable scaffolding design standard. Confirm the wall thickness and the surface condition requirements of the local scaffold code.
What documents should arrive with a steel plate shipment?
A mill test certificate (inspection certificate) with chemical composition and mechanical test values, a packing list, the bill of lading and, where required, a certificate of origin and fumigation certificate for wooden packaging.
How is a batch re-inspection organized?
Per the governing standard, material of the same grade, thickness range and heat is grouped into inspection lots, samples are cut and tested for chemical composition and mechanical properties, and the batch passes or fails as a unit. Q235 plate batches are commonly limited to 60 tonnes for re-inspection purposes.
How do I tell Q235 from Q345 visually?
You cannot reliably distinguish them visually; the grade is verified from the mill certificate and the painted grade marks on the plate. Rely on documentation and, if in doubt, a laboratory check of yield strength.
What surface defects are rejectable on mild plate?
Laminations, through-thickness cracks and deep scratches that bring thickness below the minimum tolerance are rejectable. Superficial scale and light scratches may be accepted after grinding, within the tolerance limits.

