ST12 cold rolled steel sheet is a low carbon, cold reduced flat product that has been traded under the German grade name ST12 for decades. The designation comes from DIN 1623, the German standard for cold reduced sheet, which has been withdrawn and replaced by DIN EN 10130. Under the current European system the same material is written as DC01 with the material number 1.0330, so an order for ST12 sheet and an order for DC01 sheet usually refer to one and the same class of steel. Buyers in Asia normally meet the product as JIS G3141 SPCC, in North America as ASTM A1008 CS Type B, and in China as GB/T 5213 DC01.
Grade Origin: DIN 1623, EN 10130 and the ST Series
DIN 1623 covered a series of cold reduced sheet grades that ran from St12 for simple forming work up to St14 and St15 for severe deep drawing. When EN 10130 was introduced the whole series was re-designated DC01 to DC06 and the old ST names were withdrawn. Mills and stockists continue to quote the ST12 label because it is short and well understood in the fastener, furniture, enclosure and general sheet metal trades, but the requirements that are actually applied today are those of EN 10130 or of an equivalent national standard.
DIN 1623: withdrawn German standard, former designation St12
EN 10130 and DIN EN 10130: current European standard, grade DC01, material number 1.0330
JIS G3141: Japanese standard, commercial quality grade SPCC
ASTM A1008: North American standard, CS Type B commercial steel
GB/T 5213: Chinese standard, grade DC01
Chemical Composition of ST12 and the DC Grade Family
Cold rolled forming grades are specified through their chemistry rather than through a strength class, because formability is governed mainly by carbon, manganese and the balance of the interstitial elements. The table below lists the maximum values normally applied to the ST12 equivalent DC01 grade and to the deeper drawing grades that are frequently ordered at the same time.
| Grade | C max % | Mn max % | P max % | S max % | Alt min % | Ti max % |
|---|---|---|---|---|---|---|
| DC01, formerly St12 | 0.10 | 0.50 | 0.035 | 0.025 | 0.020 | - |
| DC03, formerly St13 | 0.08 | 0.45 | 0.030 | 0.025 | 0.020 | - |
| DC04, formerly St14 and St15 | 0.08 | 0.40 | 0.025 | 0.020 | 0.020 | - |
| DC05, interstitial free | 0.008 | 0.30 | 0.020 | 0.020 | 0.015 | 0.20 |
| DC06, interstitial free | 0.006 | 0.30 | 0.020 | 0.020 | 0.015 | 0.20 |
A minimum aluminium content of about 0.020 % is required for the aluminium killed drawing grades so that nitrogen is fully combined and the risk of strain ageing is limited. The titanium bearing interstitial free grades represented by DC05 and DC06 hold carbon and nitrogen at very low levels, which is why they can survive the most severe drawing operations without stretcher strains.
Mechanical Properties, Surface Finish and Tolerances
ST12 sheet is supplied in the soft, fully annealed condition. Typical values for the grade are a yield strength in the range of 240 to 320 MPa, a tensile strength of 270 to 410 MPa and an elongation of at least 28 % measured on an 80 mm gauge length, with the exact figures depending on thickness and on the tolerances agreed for the order. The cold rolling pass gives the surface a smooth, clean appearance and closes the surface porosity left by hot rolling, which improves paint adhesion and makes the sheet suitable for visible parts.
Surface quality is ordered as finish A, B or C in the European system, while older drawings and catalogue pages often refer to the German finishes FB, higher grade finishing, and FC, high grade finishing. In practice FC means a surface free of visible defects and is chosen for exposed panels, while FB is adequate for parts that will be painted, powder coated or hidden inside an assembly.
Thickness range commonly stocked: 0.3 mm to 3.0 mm
Width range commonly stocked: 600 mm to 1500 mm
Supply forms: coil, slit strip, cut to length sheet and blanks
Standard edge condition: mill edge on coil, trimmed edge on strip and sheet
Thickness tolerance and flatness: agreed to EN 10131 or an equivalent national specification
Forming, Welding and Typical Applications
Because the carbon content is low, ST12 sheet has good plasticity and is easily bent, roll formed, embossed and blanked. It is not intended for severe deep drawing; where a drawn cup is deeper than roughly half its diameter, the drawing grades DC03 to DC06 are the better choice. Spot welding, seam welding and laser welding are all straightforward on this grade because the carbon equivalent is low and the surface is clean and free of scale.
Typical uses include electrical enclosures, cabinet and panel housings, brackets, ceiling and partition profiles, shelving, drip trays, automotive interior brackets and general pressings that need a smooth, paintable finish. When the finished part has to resist atmospheric corrosion, the cold rolled sheet is normally replaced by a zinc coated product, and hot dip galvanized material to EN 10346 or JIS G3302 is the usual substitute. Cold rolled sheet is also the substrate for organic coated coil, so the same DC01 base is frequently ordered with a paint or film finish already applied.
Handling matters as much as the grade itself. Coils and sheets should be stored on dry, level supports, and the protective oil film applied at the mill should be left in place until the parts are formed, because a dry uncoiled surface can pick up fingerprints and light surface rust within days in a humid workshop.
Common Questions About ST12 Cold Rolled Steel Sheet
Q: Is ST12 the same as DC01?
In trade terms yes. ST12 was the designation in the withdrawn DIN 1623 and DC01 is the corresponding grade in EN 10130 with material number 1.0330. The purchase order should always reference the current standard and the required surface finish.
Q: What is the difference between ST12 and SPCC?
They are equivalent commercial quality cold rolled grades from different standards. ST12 belongs to the German and European line, SPCC belongs to JIS G3141, and both are low carbon sheet intended for simple forming rather than for severe drawing.
Q: What is the tensile strength of ST12 cold rolled sheet?
Typical values fall in the range of 270 to 410 MPa, with yield strength between 240 and 320 MPa. Final acceptance values depend on thickness and on the mechanical property table of the standard named on the order.
Q: Which thicknesses and widths are available?
Material is commonly produced from 0.3 mm up to 3.0 mm thick and from 600 mm up to 1500 mm wide, supplied as coil, slit strip, cut to length sheet or blanks, with tighter ranges available on request.
Q: Can ST12 sheet be welded?
Yes. The low carbon and low carbon equivalent make it suitable for spot, seam, projection and laser welding as well as for arc welding with standard mild steel consumables.
Q: Is ST12 suitable for deep drawing?
Only for light drawing. For deeper cups and complex profiles the drawing grades DC03, DC04, DC05 or DC06 should be selected, as they offer lower yield strength, higher elongation and better forming limits.

