SPCC-SD and DC01 Black Cold Rolled Steel: Grade Equivalents and Formability

May 07, 2025 Leave a message

Decoding the Designation: SPCC-SD and DC01

SPCC is the commercial quality cold-reduced carbon steel sheet of JIS G 3141, and the suffix letters carry real information. The fourth character denotes surface finish: SPCC-SD is the dull finish supplied as standard, while SPCC-SB is the bright finish. Other letters in the same standard mark drawing qualities, SPCD and SPCE, and those grades should be specified as soon as a part involves more than simple bending. DC01 belongs to the EN 10130 family of cold-rolled low-carbon flat products for cold forming and is its basic grade; the historical designations St12 and FeP01 refer to the same material. Strip supplied without a metallic coating is often traded as black cold rolled or black annealed, which describes a mill finish rather than a surface treatment.

Cross-Standard Equivalents

Standard Grade Quality level
JIS G 3141 SPCC Commercial quality, cold reduced
EN 10130 DC01 Basic cold-forming grade of the DC family
ISO 3574 CR1 Commercial quality cold-reduced sheet
ASTM A1008/A1008M CS Type B Commercial steel of comparable chemistry and mechanical level

Equivalence means that chemistry and forming level are comparable, not that a certificate issued under one system can substitute for another. Yield strength definitions, elongation gauge lengths and surface finish tolerances differ between standards, so a specification should quote one governing standard and cite the others only as dimensional or forming references.

Chemical Composition and Mechanical Values

EN 10130 sets limits for DC01 that are widely used as the benchmark for this class of steel: carbon 0.12% maximum, manganese 0.60% maximum, phosphorus 0.045% maximum, sulphur 0.045% maximum, and aluminium 0.020% minimum for the deoxidised product. Mechanical requirements in the same standard:

Property Requirement for DC01
Yield strength ReH 280 MPa maximum
Tensile strength Rm 270 to 410 MPa
Elongation A80mm 28% minimum, thickness dependent
r-value and n-value Not specified for the basic grade

The low carbon and manganese contents explain the ductility. With carbon capped at 0.12% and no micro-alloying additions, there is very little solid-solution or pearlite strengthening available, so the material work-hardens quickly yet forms without cracking at moderate strain. Tensile testing follows ISO 6892-1 or JIS Z 2241 depending on the governing standard, and a tensile test report is meaningful only when the test direction and the gauge length are stated.

Annealing, Temper Rolling and Surface Condition

Cold rolling to final thickness leaves the strip heavily work-hardened, so an annealing step is mandatory for any forming application. Batch annealing in a bell furnace produces the dull, slightly rough surface typical of SPCC-SD together with a uniform grain structure, but the slow cycle leaves part of the carbon in solution. Continuous annealing lines produce a cleaner and more consistent recrystallised structure in minutes rather than days and are the normal route for automotive grade strip. After annealing, a light temper rolling pass of roughly 0.5 to 1.5% elongation suppresses the yield point elongation that would otherwise cause stretcher strains, the parallel bands known as Luders lines, on formed panels. Surface quality and finish are specified separately, and any oil film present is a rust-preventive and lubricating layer rather than part of the steel specification.

Forming Behaviour in Practice

SPCC-SD and DC01 handle bending, coining, beading and light drawing without difficulty. They are not deep-drawing grades. Where a part needs a drawn cup with a depth-to-diameter ratio above roughly 0.5, the specification should move to SPCD or SPCE under JIS G 3141, or to DC03, DC04, DC05 or DC06 under EN 10130. Bend practice follows thickness and rolling direction: a minimum inside radius of about one times thickness measured perpendicular to the rolling direction, increasing to about 1.5 times thickness when the bend line runs parallel to it, keeps the outer fibre below the strain that starts orange peel or cracking. Punched holes and sheared edges should be kept at least one material thickness away from a bend line, because the work-hardened burr is where cracks initiate.

Automotive and General Manufacturing Use

In vehicle manufacturing this class of steel appears as brackets, clips, battery trays, seat frame components, inner reinforcements and panel supports, where strength requirements are modest and formability governs the choice. Outside automotive it is the standard basis for electrical enclosures, furniture frames, shelving, ducting, drums and general sheet metal fabrication. Many of those parts are subsequently galvanized, painted or powder coated, in which case the uncoated mill finish is only an intermediate condition.

Corrosion Protection and Handling

Uncoated cold-rolled steel has no corrosion protection of its own. Coils are shipped with a rust-preventive oil film and should be stored under cover, away from condensation, with the laps kept tight. Where the finished part needs corrosion resistance, the sheet can be hot-dip coated to EN 10346 with designations such as Z100 or Z275, or electrolytically coated to EN 10152 with ZE designations. Choosing the coated route at the coil stage is normally cheaper than coating parts after fabrication, because coil coating is continuous and the surface is clean and uniform.

Frequently Asked Questions

Q: What is the European equivalent of SPCC?
A: DC01 in EN 10130 is the closest equivalent. ISO 3574 CR1 and ASTM A1008/A1008M CS Type B describe comparable commercial quality cold-reduced steel.

Q: What does the SD in SPCC-SD mean?
A: It identifies the dull surface finish, which is the standard finish for this grade. SPCC-SB in the same standard is the bright finish.

Q: Is DC01 suitable for deep drawing?
A: No. DC01 is the basic forming grade for bending, beading and light drawing. Deep-drawn parts need DC03 or DC04 under EN 10130, or SPCD and SPCE under JIS G 3141.

Q: Why is cold rolled coil supplied dull rather than mirror bright?
A: Batch-annealed material develops a fine rough surface during the annealing cycle. A bright finish requires different processing and is ordered as a separate finish designation.

Q: Does cold rolled steel have to be oiled?
A: Yes, for storage and transport. A light rust-preventive film prevents condensation corrosion between the laps and also acts as a lubricant in later forming operations.