A photovoltaic power station is a complete electricity-generating plant, not just a field of solar panels. Between the solar array and the grid sits a chain of equipment that collects DC power, converts it to AC, protects it from faults and monitors its performance. Buyers of steel structures for PV projects need to understand this system because the mounting structure, cable trays and equipment enclosures are all specified against the electrical design.
Classification by Capacity and Deployment
By capacity, PV stations are commonly divided into small systems below 1 MW, medium systems from 1 to 30 MW and large systems above 30 MW. By deployment, they are centralized stations, which gather power from a large array and feed the grid through a central substation, or distributed systems, which are installed at the point of use, such as rooftops, with lower-voltage grid connection. The classification drives the steel design: centralized plants use heavy fixed or tracking structures over large areas, while distributed systems use lightweight roof-mounted frames.
Core System Components
Solar Array
The solar array is the power source: photovoltaic modules mounted on steel support structures. Module orientation, tilt angle and row spacing are set for the site latitude to maximize annual yield. The mounting structure is usually hot-dip galvanized steel because it must last as long as the modules, typically 25 years.
Combiner Box
Strings of modules are connected into combiner boxes, which merge the DC circuits, house fuses or circuit breakers, and provide surge protection and monitoring points before the DC power is sent to the inverter.
DC Distribution Cabinet
The DC cabinet collects the combiner outputs, adds disconnection and protection devices, and routes the DC power to the inverter. In large plants it may include DC monitoring and arc-fault protection.
Inverter
The inverter converts DC to AC and manages the array operating point through maximum power point tracking. String inverters serve small and medium systems; central inverters serve large plants. Inverter efficiency and cooling design affect the overall plant output.
AC Distribution and Step-Up Transformer
AC output from the inverter passes through an AC distribution cabinet with protection and metering, then a step-up transformer raises the voltage for grid connection. The transformer and switchgear are commonly housed in prefabricated steel enclosures.
Tracking, Monitoring and Protection Systems
Large plants may add single-axis or dual-axis tracking systems, which rotate the array to follow the sun and increase yield at the cost of more complex steel structures and drives. A monitoring system records output, weather data and alarms, while lightning protection and earthing systems protect both the electrical equipment and personnel.
Grid Connection Voltage Levels
Small distributed systems commonly connect at 400 V low voltage. Medium plants typically connect at 10 kV or 35 kV, and large centralized plants connect at 66 kV or above through a dedicated substation. The connection voltage determines the transformer, switchgear and protection specification, and hence the size and type of steel equipment enclosures.
Why Steel Specification Matters in PV
Mounting structures and equipment racks must survive wind loads, snow loads and corrosion for decades. Hot-dip galvanized steel to EN ISO 1461 or the equivalent national standard, with coating weight selected for the site environment, is the standard answer. Structural grades such as Q235 and Q345 or equivalent are used for the frames, and the design wind speed at the site sets the section sizes.
FAQ
What is the difference between centralized and distributed PV?
Centralized plants are large ground-mounted arrays feeding the grid at high voltage; distributed plants are smaller systems at the point of use, such as rooftops, connected at low or medium voltage.
Why is the combiner box needed?
It merges the DC output of many module strings, provides fusing and surge protection, and gives a safe disconnection and monitoring point before the inverter.
Which steel is used for PV mounting structures?
Hot-dip galvanized structural steel is standard, using grades such as Q235 or Q345 for the sections, with zinc coating thickness selected for the site's atmospheric corrosivity.
How long does a PV mounting structure last?
With adequate galvanizing and correct maintenance, mounting structures are designed for the 25-year module lifetime; the galvanized coating protects the steel for the whole period in most inland atmospheres.
What voltage does a rooftop PV system connect at?
Small rooftop systems typically connect at 400 V AC through a grid-tie inverter; larger commercial rooftop systems may step up to 10 kV or 35 kV depending on local grid rules.

