Cold rolled steel coil is produced by reducing hot rolled, pickled strip at room temperature, which gives it the tight thickness tolerance, smooth surface and consistent mechanical properties that press shops depend on. The grade family behind most orders is written SPCC, DC01, DC03 or DC04, and the numbers in a specification such as 4 mm or 0.4 mm describe very different products.
What the Grades SPCC, DC01, DC03 and DC04 Mean
SPCC, SPCD and SPCE are designated in JIS G3141, where the letters cover commercial quality, drawing quality and deep drawing quality. DC01 to DC06 are the European designations for cold rolled low carbon steel flat products for cold forming, with mechanical properties and formability defined by grade. Both systems describe the same class of product, so a buyer can usually convert an enquiry from one system to the other if the drawing quality, surface finish and thickness tolerance are stated.
SPCC / DC01: commercial and general forming quality, used for bending, roll forming and simple drawn parts.
SPCD / DC03: drawing quality with improved elongation and a higher plastic strain ratio for moderate deep drawing.
SPCE / DC04: deep drawing quality for difficult profiles and severe forming.
DC05 and DC06: the highest formability levels in the same family, selected for the most demanding drawn components.
Thickness Range: 4 mm and 0.4 mm Are Not the Same Product
Cold rolled coil is normally supplied between about 0.30 mm and 3.00 mm thick, with 0.4 mm sitting in the mainstream light gauge band and 4 mm at the very top of the practical range for heavy gauge cold reduction. A 4 mm cold rolled coil is a rolling-mill product that has to be reduced step by step on a reversing mill and is usually available in a narrower width range, whereas 0.4 mm coil is a routine light gauge item. When a specification carries both figures, separate line items are needed: one for heavy gauge coil and one for light gauge coil, each with its own thickness tolerance, width and coil weight.
| Parameter | Light gauge | Heavy gauge |
|---|---|---|
| Typical thickness | 0.30-1.00 mm | 1.50-4.00 mm |
| Grain structure | Strongly work hardened, often skin passed after annealing | Higher rolling loads, greater thickness variation across the width |
| Common applications | Panels, enclosures, appliance parts, automotive inner panels | Structural brackets, drums, heavy formed sections |
| Coil inner diameter | 508 mm or 610 mm | 610 mm typical |
Mechanical Properties and Formability by Grade
Formability is described by yield strength, elongation, the plastic strain ratio r and the strain hardening exponent n. Grades with a higher r value resist thinning in the wall of a drawn cup, while a higher n value supports stretching before the material localises and tears. Deep drawing grades therefore combine a low yield strength with a controlled grain structure after annealing.
| Grade | Yield strength (MPa) | Tensile strength (MPa) | Elongation A80 (percent) | Formability marker |
|---|---|---|---|---|
| DC01 / SPCC | 140-280 | 270-410 | 28 minimum | Commercial quality, minimum tensile strength 270 MPa |
| DC03 / SPCD | 140-240 | 270-370 | 34 minimum | r90 about 1.6 and above, n90 about 0.20 |
| DC04 / SPCE | 140-210 | 270-350 | 38 minimum | r90 about 1.8 and above, n90 about 0.21 |
Chemistry supports those properties. Low carbon content keeps the ferrite soft, and typical maximum carbon levels are around 0.12 percent for DC01, 0.10 percent for DC03 and 0.08 percent for DC04, with aluminium added to fix nitrogen so that ageing is limited and forming behaviour stays stable over time.
Microstructure and Why Cold Rolled Steel Is Stronger
Cold rolling deforms the grains and multiplies dislocations, so the strip leaves the mill harder and stronger than the hot rolled material it came from. A formable grade such as DC04 is then batch or continuously annealed to recrystallise the ferrite and spheroidise the cementite, which restores ductility while keeping a fine, uniform grain size. A light temper pass after annealing sets the surface roughness and prevents stretcher strain marks during pressing. As a result, DC04 offers both a soft, low yield point and a microstructure that survives severe drawing without tearing.
Surface Finish, Flatness and Coil Parameters
Surface condition matters as much as strength when the coil is destined for visible parts or for painting. Dull, bright and extra bright finishes are available, and the chosen finish determines how the surface takes a coating and how it behaves in the press. Dimensional and flatness tolerances are normally referenced to ISO 9445 or ASTM A568/A568M, and the coil is ordered with a defined inner diameter, outside diameter and weight so that the customer's decoiler can handle it. Thickness tolerance, camber, edge condition and residual curvature all influence material yield in the press, so they belong on the purchase specification alongside the grade.
Frequently Asked Questions
Q: What is the difference between SPCC and DC01 steel?
Both describe cold rolled commercial quality low carbon sheet; SPCC comes from JIS G3141 and DC01 from the European cold forming grade system, and they are interchangeable when forming quality and tolerances match.
Q: Is 4 mm cold rolled steel coil a standard product?
It is a heavy gauge item at the extreme end of cold rolled production, usually made on a reversing mill in limited widths, and it should be quoted separately from ordinary light gauge coil.
Q: Which grade should be chosen for deep drawing?
DC03 or SPCD covers moderate deep drawing, while DC04 or SPCE is selected when the profile is difficult and elongation above 38 percent with a high plastic strain ratio is needed.
Q: Why is cold rolled steel harder than hot rolled steel?
Cold reduction at room temperature introduces work hardening, raising hardness and yield strength as the grains deform, until an annealing treatment restores ductility.
Q: What does the n value tell a press shop?
The strain hardening exponent describes how the material work hardens during stretching, so a higher n value means a more even thickness distribution and better resistance to localised necking.
Q: Which standards cover cold rolled coil tolerances and properties?
JIS G3141 covers the SPCC family, the DC grade system defines mechanical properties and forming quality, and ISO 9445 or ASTM A568/A568M is normally cited for dimensional and flatness tolerances.

