Use of cold-rolled steel in home appliances

Aug 20, 2025 Leave a message

1.What are the applications of cold-rolled steel in home appliance casings and exterior decorative parts?

Refrigerators: The refrigerator cabinet (sides and back) and door casing (metal parts other than the glass door panel) are almost exclusively made of cold-rolled steel. This is because cold-rolled steel offers a smooth surface (no oxide scale, low roughness), making it less susceptible to blemishes after powder coating or color film application. Its thickness is uniform (typically 0.3-0.8mm), allowing it to be stamped into complex curved surfaces (such as the curvature of a refrigerator door). It also provides a certain degree of rigidity to prevent deformation.
Washing Machines: The outer drum casing, control panel base, and cabinet casing of front-loading washing machines are often made of cold-rolled steel. In front-loading washing machines, in particular, the casing must withstand the slight vibrations of the rotating drum. The yield strength of cold-rolled steel (typically 200-350 MPa) provides sufficient structural support. Furthermore, after phosphating and spray-coating, the surface resists rust in humid environments.
Air Conditioners: The indoor unit casings of split-type air conditioners (such as the front panel of wall-mounted units and the side casings of cabinet units) and the outdoor unit outer casing (protecting the internal compressor and condenser) are commonly made of cold-rolled steel. The outdoor unit casing needs to withstand outdoor weather and wind. Cold-rolled steel is pickled, galvanized (some products are "cold-rolled galvanized steel," meaning the steel is galvanized on top of the cold-rolled steel sheet), and then sprayed with a special outdoor paint to enhance corrosion resistance. For the indoor unit casing, the focus is on surface smoothness, ensuring no bumps or indentations after spraying or applying a decorative film, ensuring aesthetic appeal.

Small appliances, such as microwave oven casings, oven sides/tops, and metal water heater casings (especially the cylindrical casings of storage water heaters), are also often made of cold-rolled steel. These small appliance casings are relatively small, and the high dimensional accuracy of cold-rolled steel (thickness deviation ≤ ±0.02mm) ensures consistent assembly during mass production (e.g., ensuring the proper fit between the casing and internal components).

cold-rolled steel

2.What are the applications of cold-rolled steel in internal structural parts and functional components?

Structural support components: Refrigerator liner support frames (the metal framework that secures the evaporator and insulation), washing machine drum support brackets (the metal frame connecting the drum to the motor), and air conditioner indoor unit duct frames (the frame that secures the fan and evaporator) are all stamped or bent from cold-rolled sheet. The rigidity of cold-rolled sheet (strengthened through cold working, resulting in a higher hardness than hot-rolled sheet) ensures these components withstand long-term stress without deformation. For example, the drum bracket of a washing machine must bear the weight of rotating laundry, and its bending resistance prevents breakage.
Functional connectors: Microwave oven door hinges (connecting the door to the oven and requiring repeated opening and closing), oven tray rails (supporting tray movement), and refrigerator drawer guides are often made from cold-rolled sheet. These components require a certain level of wear resistance and toughness. Stamping results in smooth edges for cold-rolled sheet (without the burrs typically associated with hot-rolled sheet). Subsequent heat treatment (such as partial quenching) can increase surface hardness and extend service life. Load-bearing components: The bases of some large household appliances (such as refrigerator bases and cabinet air conditioner bases) need to bear the weight of the entire appliance. Thicker cold-rolled plates (1.0-2.0mm thick) are used and bent into a "U-shaped" or "L-shaped" structure. The compressive strength of the cold-rolled plates is used to distribute the weight and prevent the base from collapsing.

cold-rolled steel

3.What are the surface quality requirements for cold-rolled steel for home appliances?

No scale or rust: Cold-rolled steel is produced by cold-rolling (room temperature rolling) hot-rolled steel. Before rolling, it undergoes pickling to remove scale, resulting in a smooth, clean surface free of the iron oxide residue often found on hot-rolled steel. This is a prerequisite for subsequent coating (powder coating or painting). If scale is present on the surface, it can easily cause bubbling and peeling after painting.

Low roughness (Ra value): Surface roughness Ra ≤ 1.6μm is generally required (some high-end appliances require ≤ 0.8μm). Low roughness results in a smoother surface, resulting in a uniform coating thickness after powder coating, less prone to "orange peel" (uneven coating surface), and a tight, bubble-free adhesion when applying color film. No scratches or pitting: If there are defects in the rolling rollers during the cold rolling process, scratches and pitting will appear on the surface of the steel plate. Such defects will directly affect the appearance of home appliances (even painted ones may show marks). Therefore, most cold-rolled steel plates used in home appliances have a "high-grade surface" (such as the "SPCC-SD" grade in the industry standard, which means "special annealed flat" and has very few surface defects).

cold-rolled steel

4.What are the mechanical property requirements for cold-rolled steel for home appliances?

Ductility (Elongation): Stretchable components (such as the curved panels of refrigerator doors) require cold-rolled steel sheets with good ductility, typically requiring an elongation of 25% or higher (for example, low-carbon cold-rolled steel with a carbon content of 0.12% or lower exhibits excellent ductility) to avoid cracking or wrinkling during stretching.
Yield Strength: Structural components (such as brackets and bases) require a certain strength, typically 200-300 MPa. If the yield strength is too low, deformation after forming may occur (for example, a washing machine bracket bending under load). If it is too high, greater force is required during stamping, which can lead to mold wear and cracking at the bends due to excessive rigidity.
Uniformity: The mechanical properties (such as hardness and elongation) of cold-rolled steel sheets within a batch must be uniform. Otherwise, during batch stamping, some parts may pass the forming process while others may crack or deform, impacting production efficiency.

 

5.What are the requirements for dimensional accuracy of cold-rolled steel for home appliances?

Thickness Tolerance: The thickness of exterior parts is typically 0.3-0.8mm, with a tolerance of ≤±0.02mm. Uneven thickness can lead to uneven force during stamping, causing deformation. Furthermore, coating thickness can vary during painting due to fluctuations in steel plate thickness (thin coating on thicker plates and thicker coating on thinner plates, affecting appearance).
Plate Width and Straightness: Cold-rolled steel must be flat (free of warping or lateral bending) after rolling, with a plate width tolerance of ≤±0.5mm. Otherwise, uneven dimensions will occur during cutting, resulting in component misalignment during subsequent assembly (e.g., uneven gaps between refrigerator housing and door).