Two galvanized square tubes with identical dimensions can differ by five to one in outdoor service life. The difference is not the brand on the tube; it is the amount and condition of the zinc on the surface, the environment it faces and the way the fabrication details handle water.
Factor One: Coating Mass and Thickness
Coating mass is the zinc reserve, and service life is largely a question of how long that reserve lasts. Hot-dip galvanized tube in structural service is normally specified to a coating thickness in the range of 45 to 85 micrometres per side, consistent with the tables of ISO 1461, which requires an average coating thickness of 85 micrometres on steel at least 6 mm thick with a minimum local value of 70 micrometres. In grams per square metre, an 85 micrometre coating holds roughly 610 g/m2 of zinc.
Converting coating mass into years requires the site corrosivity category. ISO 9223 defines categories C1 to CX and gives first-year zinc mass loss for each; a C3 category corresponds to 5 to 15 g/m2 in the first year. Dividing the available zinc by that annual loss puts an 85 micrometre coating in the range of several decades in a C3 atmosphere and considerably less in a coastal C5 site. Coating thickness should therefore be set from the corrosivity category, never from a default specification carried over from an inland project.
Factor Two: Adhesion and the Alloy Layer
Zinc that is present but unbonded provides no protection. The protective value of a coating depends on a continuous iron-zinc alloy layer at the interface, which forms during immersion in the zinc bath and is governed by surface cleanliness and by the aluminium content of the melt, normally held between 0.15 and 0.25 percent. If the substrate enters the bath with oxide, oil or scale on the surface, the alloy layer becomes discontinuous and the coating can lift during transport, bending or site handling.
Adhesion is verified with simple field tests. A hammering test is described in GB/T 13912-2022, and a 180-degree bend test is a common acceptance check: a coating that neither cracks nor lifts from the substrate under bending demonstrates adequate bonding. For tube galvanized in automatic plants, EN 10240 defines coating classes that include an internal surface requirement, which matters because the inside of a hollow section is inaccessible after fabrication.
Factor Three: Passivation Treatment
Freshly galvanized zinc is chemically active. In damp storage or during sea transport, white corrosion product forms on the surface, and a passivation layer applied at the end of the line is what slows that reaction. Chromate-based passivation has been progressively restricted, and chromium-free alternatives based on silane or other organic film formers are now standard. Passivation is not a substitute for coating thickness, but a coil or tube without it will show white rust long before its zinc reserve is consumed.
Passivation also affects downstream processing. A heavy passivation film can interfere with paint adhesion, so if the tube will be coated later, the passivation type must be agreed between the tube producer and the coater at the order stage.
Factor Four: Environmental Corrosivity
Humidity, chloride and airborne pollutants drive the consumption rate of zinc. Coastal sites, de-iced road environments and industrial atmospheres with sulphur compounds fall in the higher ISO 9223 categories and consume zinc several times faster than the rural or light urban conditions usually assumed in generic service life claims. Where the environment cannot be changed, the design response is either a heavier coating or a duplex system in which a paint layer is applied over galvanized steel, so that the paint carries the atmospheric attack and the zinc provides protection at any break in the film.
Factor Five: Storage and Handling Before Installation
White rust that appears in the yard is a logistics defect, not a coating defect. It forms when tubes are stored in humid conditions above roughly 60 percent relative humidity without ventilation, or when a stack is wrapped airtight before the coating is fully dry. The countermeasures are simple and effective: keep stacks off the ground on dunnage, leave gaps between bundles for air movement, avoid sealing moisture inside packaging and use desiccants for long sea voyages. Where tube must be stored for months before erection, a heavier coating class and a proven passivation system are cheaper than repainting the yard stock.
Factor Six: Design and Fabrication Detailing
The last factor is in the fabricator's hands. Water that cannot drain accelerates corrosion at any coating break, so hollow sections should be sealed at the ends or drilled for drainage, gussets should not create pockets, and connections should be detailed so that moisture runs off rather than sitting on a ledge. Cut ends and drilled holes expose bare steel; on a batch-galvanized tube they are already coated, but on continuously coated tube they need a compatible repair coating. Field welds destroy the coating locally and must be repaired with a zinc-rich product of a type permitted by the governing standard.
| Factor | Practical control | Verification |
|---|---|---|
| Coating thickness | Select class from ISO 9223 corrosivity category | Magnetic gauge to EN ISO 2178 |
| Coating mass | Specify minimum g/m2 per surface | Gravimetric to EN ISO 1460 or ASTM A90/A90M |
| Adhesion | Control bath chemistry and surface cleanliness | Hammering and 180-degree bend |
| Passivation | Chromium-free system agreed with downstream coater | Coating weight and paint adhesion checks |
| Storage | Ventilated stacking, desiccants, dry before packing | Visual inspection at goods-in |
| Detailing | Drainage holes, sealed ends, repaired field welds | Dimensional and coating inspection at handover |
Frequently Asked Questions
Q: What coating thickness gives fifteen to twenty years of outdoor life?
A: Roughly 65 to 85 micrometres per side is the usual range for that expectation in a C2 to C3 atmosphere under ISO 9223. In a coastal C5 category the same coating is consumed several times faster and a duplex system is normally required.
Q: How is zinc layer adhesion tested on square tube?
A: Two field methods are used. A hammering test as described in GB/T 13912-2022, and a 180-degree bend test in which the coating must neither crack nor lift from the substrate.
Q: What causes white rust and how is it prevented?
A: White rust is zinc oxide and hydroxide formed when the coating stays wet. It is prevented by ventilated dry storage, desiccants in packaging for long transport, and a passivation layer applied at the end of the galvanizing line.
Q: Which standards apply to galvanized square tube?
A: Tube production follows welded tube standards such as GB/T 3091-2015 for low-pressure fluid service, while coating requirements follow GB/T 13912-2022 or ISO 1461. Tubes galvanized in automatic plants can also be specified to EN 10240 coating classes.
Q: Do cut edges reduce corrosion resistance?
A: On batch-galvanized tube the cut faces are already coated. On continuously coated tube the sheared edge exposes steel, and it should either be positioned away from moisture or treated with a compatible zinc-rich repair coating.
Q: How does compressive capacity relate to the coating?
A: The coating does not add structural capacity. Axial compressive capacity is governed by the steel grade, wall thickness and section geometry, so capacity should be calculated from the base material properties.

