Q345B Steel in Building Structures: Applications and Design Considerations

Aug 26, 2025 Leave a message

What Q345B Is and Where It Sits in the Standards

Q345B is a low-alloy structural steel specified in GB/T 1591-2008 with a minimum yield strength of 345 MPa for thickness up to 16 mm. The letter B denotes the quality class, which guarantees a Charpy V-notch impact test at +20 C; the same chemistry is also supplied as Q345C tested at 0 C and Q345D tested at -20 C for colder service. When GB/T 1591-2018 replaced the earlier edition the grade was renumbered as Q355B, with a minimum yield strength of 355 MPa. Older drawings and existing structures therefore still refer to Q345B, and both designations describe the same family of micro-alloyed, readily weldable structural steel supplied as plate, wide strip, H-sections, angles and hollow sections.

Compared with Q235, Q345B delivers roughly 47 % more yield strength at a modest price premium; compared with Q390 and Q420 it is cheaper, easier to weld and far less demanding on preheat. That balance is why it remains the default structural grade across a very wide band of building work.

Property Q235B Q345B Q390B
Min. yield strength, MPa, thickness up to 16 mm 235 345 390
Tensile strength, MPa 370 to 500 470 to 630 490 to 650
Elongation, min. % 26 21 20
Impact test temperature +20 C +20 C +20 C

The comparison values come from the same standard family and are given for orientation only; the figures for the thickness and delivery condition actually ordered must always be taken from the mill certificate.

High-Rise and Super High-Rise Buildings

Columns and floor beams are the flagship application. Because Q345B carries more stress per unit area than Q235, design studies for tall buildings typically report that the cross-sectional area of a column can be reduced by roughly 15 to 30 % when the grade is upgraded, which increases usable floor area, lowers structural dead load and eases foundation design. The benefit grows with height, and super high-rise towers above about 100 m are the clearest case for the grade.

In buildings with demanding seismic fortification requirements, Q345B is also used for the diagonal braces between frames and for the edge members of shear walls. Its combination of strength and toughness raises the energy that the structure can absorb before collapse, which is exactly the property that ductile seismic design depends on. Where the design calls for even lower transition temperatures, the C and D classes are specified instead of B.

Long-Span Roofs, Halls and Small-to-Medium Bridges

Steel roof trusses, space grids and portal frames in stadiums, exhibition halls, convention centres and airport buildings all rely on the grade. Replacing Q235 with Q345B in the main beams of a long-span portal frame typically allows steel consumption to be reduced by roughly 10 to 20 % while still satisfying the deflection and load-carrying limits that govern long spans, because the design is usually stiffness-controlled rather than strength-controlled.

In bridge work, large crossings generally use dedicated bridge steels such as Q370q or Q420q, but Q345B remains common for the main girders and pier bearings of small and medium municipal bridges, particularly simply supported and continuous beam spans of about 30 m or less, where it offers the most economical solution.

Industrial Buildings and Special Structures

Heavy machinery plants, metallurgical workshops and shipyards use Q345B for crane runway beams, columns and roof purlins. Crane girders are the critical case: with cranes of 50 t and above the member is subjected to millions of load cycles, and the higher strength of Q345B keeps stresses and deflections within fatigue limits that a Q235 section could not meet economically. Fabricated plate girders in this application also benefit from the good weldability of the grade.

Special structures include steel chimneys, water tower supports, tank and silo supports, and the steel foundations of lifting equipment. These members resist vertical loads from the tank or vessel together with horizontal wind and seismic loads, and the balanced strength and toughness of the grade keep the structure stable without an expensive alloy upgrade.

Composite Beams and Concrete-Filled Columns

Composite construction is one of the fastest growing uses. In a composite floor beam a Q345B steel section carries tension while the concrete slab above carries compression, connected by shear studs, so a shallower and lighter beam achieves the same capacity and stiffness. Composite columns take the principle one step further: a Q345B steel tube filled with concrete acts as a core column in a tall building, combining the hoop restraint and high strength of the steel with the compressive resistance of the concrete, which improves both axial capacity and fire performance.

Where a bare steel member would need heavy fire protection, the concrete inside a filled tube also contributes to the fire rating, reducing the thickness of applied protection or removing the need for it altogether on the column.

Fabrication, Welding and Protection

Q345B is normally welded without preheat for moderate thickness, which is one of its main advantages over Q390 and Q420. Preheat becomes advisable as plate thickness and restraint increase, and the carbon equivalent and the welding procedure should be taken from the mill certificate. Consumables matched to the strength of the base metal, controlled heat input and dimensional checks after welding keep distortion within tolerance.

Corrosion protection is usually paint or a metallic coating, and galvanizing is common for exposed secondary framing. Fire protection is provided by intumescent coatings, spray-applied vermiculite or boards, sized according to the section factor and the required fire resistance period.

Frequently Asked Questions

Q: What types of building structure is Q345B used for?
It is used for high-rise columns, beams and braces, long-span roofs and halls, crane runway beams in industrial buildings, small and medium bridge girders, and composite beams and concrete-filled columns.

Q: Is Q345B still a valid grade?
Yes. Q345B appears in GB/T 1591-2008 and in older drawings; GB/T 1591-2018 renumbered the equivalent grade as Q355B with a slightly higher minimum yield strength.

Q: Does Q345B need preheating before welding?
Not for ordinary thickness. Preheat becomes advisable for thick plate, high restraint joints and cold ambient conditions, with values taken from the certified welding procedure.

Q: Why is Q345B preferred over Q235 for tall buildings?
Its higher yield strength allows smaller sections, which reduces structural dead load and increases usable floor area, while still providing the toughness needed for seismic design.

Q: When should Q345C or Q345D be used instead of Q345B?
Choose the C or D class when the structure will see service temperatures around 0 C or -20 C and impact toughness must be verified at those temperatures.

Q: Can Q345B be used in composite construction?
Yes. It is widely used for composite floor beams and for concrete-filled steel tube columns, where the steel and concrete share the load efficiently.