Raw Material Cost: Cold-Rolled Coil and Zinc
Cold-rolled galvanized corrugated sheet is built from two purchased commodities, cold-rolled steel coil and zinc, and their price movements pass almost directly into the offer sheet. Cold-rolled coil follows iron ore, coking coal and scrap prices, mill energy costs and the balance between mill order books and available capacity. Zinc follows ore supply, treatment charges and the development schedule of new mines, so a tight concentrate market shows up as a higher zinc price with a lag of a few weeks.
The zinc contribution is larger than many buyers expect, because it scales with coating mass rather than with steel volume. A square metre of 0.5 mm sheet weighs roughly 3.9 kg, and at the Z275 designation that square metre also carries about 275 g of zinc, so the coating is close to seven per cent of the finished mass. A coating upgrade from Z140 to Z275 therefore changes both the coating cost and the price base of the sheet, not just a finishing add-on.
| Input | What moves it | Direction on sheet price |
|---|---|---|
| Cold-rolled substrate | Iron ore, scrap, mill energy and order book | Direct, largest single component |
| Zinc | Concentrate supply, mine development, treatment charges | Direct, proportional to coating mass |
| Energy and utilities | Electricity and gas tariffs, seasonal peaks | Indirect, through both steel and coating lines |
Galvanizing Route and Coating Specification
The coating route carries its own cost stack. Hot-dip galvanizing involves a molten zinc bath, flux or pre-treatment, controlled line speed and post-treatment cooling, and it usually delivers a heavier, more durable coating, so the product price is higher. Electrogalvanizing produces a thinner, more uniform coating and is generally cheaper per unit area, which suits painted parts and indoor applications where a thin coating is adequate.
Coating mass such as Z100, Z140, Z275 or Z350 sets zinc consumption and price directly.
Alloy coatings and zinc-aluminium-magnesium coatings add bath alloying cost but improve durability in aggressive environments.
Passivation, oiling and anti-fingerprint treatment add a process step and a consumable cost that appears as a line item.
Spraying, printing or film lamination applied to the finished corrugated sheet raise cost further and turn the item into a decorative product.
Sheet Geometry and Corrugation Profile
Geometry decides how much steel is needed to cover a given roof or wall area, which is why two sheets with the same nominal thickness can differ substantially in price per square metre of finished cladding.
| Parameter | Material effect | Price effect |
|---|---|---|
| Base thickness | 0.8 mm consumes far more steel than 0.3 mm per unit area | Approximately proportional to thickness |
| Coil width | Wider coil reduces the number of passes for the same covered area | Lower cost per covered square metre |
| Wave height | Deeper corrugation needs more developed width per covered width | Higher, plus tooling constraints |
| Wave pitch | Closer pitch increases forming stations and load | Higher tooling and conversion cost |
Roll forming adds conversion cost through tooling, line time and scrap at the head and tail of each coil. A profile that is difficult to form without coating damage also raises reject rates, and that cost is eventually priced into the product.
Order Quantity, Packaging and Freight
Commercial cost is not only factory cost. Small or mixed orders require more handling, more setups and more packing per tonne, so unit prices rise. Full coil orders of a single specification are the cheapest way to buy; cut-to-length, slit or short-run requirements carry a premium.
Order size and specification uniformity determine setup and handling cost per tonne.
Packing such as eye-to-sky, eye-to-wall, wooden pallets, edge protection and moisture barrier film adds cost but reduces transit damage.
Transport mode and distance change freight substantially; container loading efficiency depends on sheet length and bundle design.
Taxes, duties and currency movement can outweigh production cost differences between suppliers.
Market Supply, Demand and Seasonality
Finally, price is set where supply meets demand, not where cost ends. During peak construction season demand for cladding material rises and prices firm; in the off-season, when distributors hold inventory and mills compete for order books, prices soften. Mill maintenance outages, environmental production restrictions and sudden changes in export policy can tighten supply within weeks, while a slow construction market can leave stock overhanging and depress prices even when raw material costs are unchanged.
Buyers who need predictable budgets therefore track three indicators together: the cold-rolled coil index, the zinc price and the local construction cycle. Buying against a fixed specification and a realistic lead time is usually cheaper than chasing a speculative low in a volatile quarter.
Frequently Asked Questions
Q: Which raw material affects the price the most?
Cold-rolled substrate, because it dominates the mass of the product; zinc is second but scales with coating mass and can move quickly on its own cycle.
Q: Is hot-dip galvanized corrugated sheet always more expensive than electrogalvanized?
Usually yes per unit area, because the molten bath process and heavier coating cost more, though the longer service life can lower total cost over the structure's life.
Q: How much can thickness change the price?
Substantially. Going from 0.3 mm to 0.8 mm raises the steel content per square metre by well over double, and price roughly follows that material increase.
Q: Why do small orders cost more per tonne?
Because setup, handling, packing and freight are spread over fewer tonnes, so fixed costs per unit rise even when the material is identical.
Q: Why can prices fall even when raw material costs are stable?
Because price reflects supply and demand. Weak construction demand and high distributor inventory can push offers below the cost floor while mills compete for volume.
Q: Does a heavier coating always raise the price a lot?
It raises the zinc cost, which is proportional to coating mass; at Z275 the coating is roughly seven per cent of finished sheet mass, so the effect is real but secondary to substrate price.

