What Surface Quality Means on a Galvanized Sheet
Surface quality of a hot-dip galvanized sheet is not a single measurement. It is a set of independent checks that fall into four groups: coating quantity, coating appearance and continuity, coating adhesion, and the condition of the chemical surface treatment. A sheet that passes one group can still fail another, so acceptance is normally written as a list of indicators with a test method and a rejection limit for each.
Indicator 1: Coating Mass and Thickness
Coating quantity is the base indicator, because corrosion life scales with the mass of zinc present. EN 10346 states coating mass in grams per square metre as a nominal value with minimum triple-spot and minimum single-spot limits, while ASTM A653/A653M states it in ounces per square foot. The gravimetric method of ISO 1460 and the strip weighing method of ASTM A90/A90M dissolve the coating and weigh the result, and they remain the referee methods when a dispute arises. Magnetic thickness gauges per ISO 2178 are used for fast line checks, but they must be calibrated against the actual coating system, because probe geometry and surface roughness bias the reading.
| Indicator | Method | What it catches |
|---|---|---|
| Coating mass | ISO 1460 / ASTM A90 | Underweight coating, one-sided coating |
| Coating thickness | ISO 2178 magnetic gauge | Local thin spots, edge effects |
| Adhesion | Bend and draw test on finished parts | Flaking, peeling, powdering |
| Surface appearance | Visual against a reference sample | Dross, pimples, streaks, scratches |
| Passivation film | Spot chemical test, white cloth wipe | Bare or partially passivated areas |
| Oil film | Wipe test, gravimetric oil mass | Dry areas, excess oil, staining |
Indicator 2: Coating Continuity and Appearance
The visual check looks for the defect families that matter in forming and painting, not for cosmetic perfection. Zinc dross and pimples are hard particles rolled into the surface; they damage drawing dies and cause paint pinholes. Streaks and banding indicate air-knife instability and produce coating mass variation along the length. Bare edges, uncoated spots and edge over-thickness come from bath and edge-control problems. Spangle is the visible crystallisation pattern of the zinc; its size is controlled mainly by cooling rate and by additions to the zinc bath, and spangle size does not change corrosion resistance or mechanical properties. Normal spangle, minimised spangle and skin-passed surfaces are all available from EN 10346, and the choice is an appearance and downstream-processing decision rather than a durability decision.
Indicator 3: Adhesion and Forming Behaviour
Coating adhesion is judged by subjecting the sheet to the worst deformation it will see in production and then inspecting the coating. A bend or draw test performed on finished parts is more informative than a flat-panel test, because failure usually starts at a sheared edge or in a tight radius. Reported findings are flaking of zinc, powdering of the coating, cracking along the bend line and coating loss on the cut edge. For sheets intended for deep drawing, adhesion is checked together with the substrate's own forming behaviour, since a zinc coating can only follow the strain its base metal can take without local thinning.
Indicator 4: Passivation, Oiling and Transport Protection
Chemically passivated surfaces are checked for coverage rather than for chemistry on the shop floor. A clean white cloth wiped across the surface should come away free of grey or white residue, which signals zinc corrosion product. A spot test with a colour-forming reagent reveals whether the passivation film covers an area evenly; a localised absence of film is where white rust will start in a humid container. Oil film is measured qualitatively with a wipe test and quantitatively by extracting and weighing the oil, and the target is a continuous film thick enough to protect the surface but thin enough not to interfere with downstream painting or welding.
Indicator 5: Performance Checks That Reflect the End Use
For exposed or decorative applications, the acceptance criteria shift towards uniformity: colour and gloss consistency across a coil, freedom from fatal defects, and a low count of minor marks. For stamping and bending, the criteria shift towards formability and edge integrity. Where corrosion performance must be demonstrated rather than assumed, accelerated exposure in neutral salt spray per EN ISO 9227 or ASTM B117 is used, and results are reported as hours to first white rust and hours to first red rust. EN 10346 does not fix salt-spray durations, so the hours required are agreed between buyer and supplier for the specific coating mass and end use.
Frequently Asked Questions
Q: Which single indicator is most important for surface quality?
A: Coating mass. It is the only indicator that directly sets corrosion life; the remaining checks protect formability, appearance and downstream painting.
Q: Does spangle size affect corrosion resistance?
A: No. Spangle is a crystallisation pattern produced during solidification. It affects appearance and paint uniformity, not coating mass or corrosion life.
Q: How is coating mass verified in a dispute?
A: By the gravimetric stripping method of ISO 1460 or ASTM A90/A90M, taken from defined triple-spot locations and compared with the minimum limits of the ordering standard.
Q: Can a magnetic gauge replace laboratory coating mass testing?
A: It can be used for routine line checks, but it must be calibrated on the same coating system and is not a referee method. Gravimetric testing remains the accepted reference.
Q: What causes white rust in transit?
A: Condensation on inadequately passivated or unoiled surfaces. Correct passivation, controlled oiling and moisture-barrier packing are the usual countermeasures.
Q: Why do sheared edges show coating damage?
A: Shearing cuts the coating rather than deforming it, exposing bare steel at the edge. The edge is then protected by the sacrificial action of the surrounding zinc, which is why coating mass still governs edge performance.

