What Is a Galvanized Coil?

Oct 13, 2025 Leave a message

What Is a Galvanized Coil?

A galvanized coil is a cold-rolled or hot-rolled steel coil that has been coated with a zinc layer to protect the steel from corrosion. In continuous hot-dip galvanizing, the strip is cleaned, annealed and passed through a bath of molten zinc at approximately 450-460 degrees Celsius, then wiped with gas knives to control coating thickness. The result is a metallurgically bonded zinc coating that provides barrier protection and galvanic (sacrificial) protection at cut edges and scratches.

Hot-Dip versus Electro-Galvanized Coil

Parameter Hot-dip galvanized Electro-galvanized
Typical coating weight 50-275 g/m2 per side class 10-50 g/m2 per side
Coating structure Metallurgical alloy layers with spangle Uniform thin pure zinc layer
Corrosion resistance High, long service life Lower, mainly for indoor parts
Typical standards EN 10346, JIS G3302, ASTM A653 EN 10152, ASTM B633 (parts)
Typical applications Roofing, framing, ducts, agricultural buildings Automotive interior parts, electronics, appliances

Coating Designations and Coating Weight

In EN 10346 the coating is designated by the letter Z (pure zinc) or ZF (zinc-iron alloy) followed by the coating mass in grams per square metre for both surfaces together. Common classes are Z100, Z120, Z140, Z180, Z200 and Z275. JIS G3302 uses F06 to F18 classes, and ASTM A653 uses the same Z-class system (Z100, Z180, Z275 and others) with coating weight measured in g/m2.

Coating class Coating mass (g/m2, both surfaces) Typical use
Z100 100 Light interior components
Z140 140 General building components
Z180 180 Profiled sheets, purlins
Z275 275 Highly corrosive environments, roofing

Base Metal Grades

The base steel is specified by the product standard: DX51D to DX57D in EN 10346 for cold forming, SGCC in JIS G3302, and CS Type A/B, DS Type A/B or structural grades in ASTM A653. Galvannealed (ZF) coatings are produced by heating the coated strip to about 500 degrees Celsius to alloy the zinc with iron, giving a dull grey surface that welds and paints more easily and is commonly used in automotive bodies.

Frequently Asked Questions

What does Z275 mean?

Z275 means a total zinc coating mass of 275 g/m2 measured on both surfaces of the strip, specified in EN 10346 and ASTM A653. It is one of the highest coating weights commonly supplied and is used for severe corrosion environments.

Is galvanized coil the same as aluminium-zinc or zinc-aluminium-magnesium coil?

No. Galvanized coil has a pure zinc coating. aluminium-zinc (AZ, aluminium-zinc) and zinc-aluminium-magnesium (ZM) coatings are different alloy systems with different corrosion behaviour, specified in EN 10346 classes AZ and ZM.

Can galvanized coil be painted?

Yes. The surface is normally pre-treated (cleaning and conversion coating) before painting, and most painted steel starts from hot-dip galvanized substrate in a coil coating line.

Does galvanized coil resist scratches?

Scratches through the zinc layer are protected by the galvanic action of the surrounding zinc, which corrodes preferentially and protects the exposed steel. This sacrificial protection is a key advantage of zinc coatings.

How should galvanized coil be stored?

Coils should be stored indoors or under cover, tilted or on a rack so that water cannot collect, and separated from bare steel, moisture and chemicals to avoid white rust formation. Storage beyond a few months may require additional protection such as vapour-phase inhibitors.

What is white rust?

White rust is the light, powdery zinc corrosion product that forms when freshly galvanized surfaces stay wet for long periods in poorly ventilated storage. It is mostly cosmetic, but heavy cases can reduce coating life, so dry storage is important.